DOWNLOAD JBL CS60.2 (serv.man2) Service Manual ↓ Size: 479.51 KB | Pages: 8 in PDF or view online for FREE

SETTING THE
CROSSOVER(S)
Determine your system plans and set the
crossover mode switch accordingly. 
If your system design does not include a
subwoofer with the CS60.4, set the
crossover mode to FLAT and skip to
“Setting Input Sensitivity”.

Initially set the crossover frequency 
control midway. While listening to music,
adjust the crossover for the least perceived
distortion from the speakers, allowing them
to reproduce as much bass as possible. 

Systems using a separate subwoofer set
the crossover mode to HP (high pass) for
your full-range speakers. Adjust the
crossover frequency to limit bass and
provide increased system volume with less
distortion.

For subwoofers, choose the highest 
frequency that removes vocal information
from the sound of the subwoofer.

If using the CS60.4 or CS60.2 to drive a 
subwoofer(s), set the crossover mode to 
LP (low pass).

SETTING INPUT
SENSITIVITY
1. Initially turn the INPUT LEVEL control(s)

to minimum (counter clockwise).

2. Reconnect the (–) negative lead to the

vehicle’s battery. Apply power to the
audio system and play a dynamic music
track.

3. On the source unit, increase the volume

control to 3/4 volume. Slowly increase
the INPUT LEVEL control(s) toward three
o’clock until you hear slight distortion 
in the music. Then reduce the INPUT
LEVEL slightly until distortion is no longer
heard. 

NOTE: After the source unit is on, blue
LEDs (on the top panel) will light, indicating
the amplifier is on. If not, check the wiring,
especially the remote connection from 
the source unit. Also refer to
“Troubleshooting” guide at right.

No audio 

No voltage at BATT+ 

Check voltages at

(POWER LEDs

or REM terminals, 

amplifier terminals

are off)

or bad or no ground 

with VOM

connection

No audio 

Amplifier is

Make sure amplifier

(POWER

overheated

cooling is not blocked

LEDs are on)

at mounting location;
verify speaker-system
impedance is within 
specified limits

Voltage more than 16V

Check vehicle

or less than 8.5V on

charging system

BATT+ connection

No audio

Voltage less than 9V on 

Check vehicle

(POWER BATT+ 

connection

charging 

system

LEDs flash) 

DC voltage on 

Amplifier may need

amplifier output 

service; see enclosed
warranty card for
service information 

Distorted audio

Input sensitivity is 

Check INPUT 

not set properly, or

LEVEL setting; or

amplifier or source 

check speaker wires

unit is defective

for shorts or grounds

Distorted audio

Short circuit in 

Remove speaker leads

and POWER 

speaker or wire

one at a time to locate

LEDs flash

shorted speaker or 
wire, then repair 

Music lacks 

Speakers are not 

Check speaker

“punch”

connected properly

connections for
proper polarity

Declaration of Conformity

We, Harman Consumer Group International

2, route de Tours
72500 Chateau du Loir
France

declare in own responsibility that the products
described in this owner’s manual are in compliance
with technical standards:

EN 55013:2001 + A1:2003
EN 55020:2002 + A1:2003

Klaus Lebherz

Harman Consumer Group

International

Chateau du Loir, France 7/05

JBL Consumer Products 
250 Crossways Park Drive 
Woodbury, NY 11797 USA

JBL is a trademark of Harman International 
Industries, Incorporated, registered in the 
United States and/or other countries.

Part No. CSAMPOM7/05

• 200W RMS x 1 channel at 4 ohms and ≤1% THD + N
• Signal-to-noise ratio: 75dBA (reference 1W into 4 ohms)

• 300W RMS x 1 channel at 2 ohms, 14.4V supply and ≤1% THD + N
• Dynamic power: 460W at 2 ohms

• Effective damping factor: 6.395 at 4 ohms

• Frequency response: 10Hz – 300Hz (–3dB)

• Maximum input signal: 7,5V

• Maximum sensitivity: 100mV

• Output regulation: –0.07dB at 4 ohms

• Dimensions (L x W x H): 322 x 260 x 56mm (12-11/16" x 10-1/4" x 2-3/16")

• Fuses: 20A x 2

• 60W RMS x 4 channels at 4 ohms and ≤1% THD + N
• Signal-to-noise ratio: 75dBA (reference 1W into 4 ohms)

• 80W RMS x 4 channels at 2 ohms, 14.4V supply and ≤1% THD + N
• 160W RMS x 2 channels at 4 ohms, 14.4V supply and ≤1% THD + N
• Dynamic power: 145W at 2 ohms

• Effective damping factor: 6.395 at 4 ohms

• Frequency response: 10Hz – 27kHz (–3dB)

• Maximum input signal: 6V

• Maximum sensitivity: 100mV

• Output regulation: –0.03dB at 4 ohms

• Dimensions (L x W x H): 337 x 260 x 56mm (13-1/4" x 10-1/4" x 2-3/16")

• Fuses: 25A x 2

• 60W RMS x 2 channels at 4 ohms and ≤1% THD + N
• Signal-to-noise ratio: 75dBA (reference 1W into 4 ohms)

• 80W RMS x 2 channels at 2 ohms, 14.4V supply and ≤1% THD + N
• 160W RMS x 1 channel at 4 ohms, 14.4V supply and ≤1% THD + N
• Dynamic power: 160W at 2 ohms

• Effective damping factor: 6.395 at 4 ohms

• Frequency response: 10Hz – 27kHz (–3dB)

• Maximum input signal: 6V

• Maximum sensitivity: 100mV

• Output regulation: –0.03dB at 4 ohms

• Dimensions (L x W x H): 225 x 260 x 57mm

(8-7/8" x 10-1/4" x 2-1/4")

• Fuses: 25A x 1

This product is intended for mobile applications without connection to the 
110/230 volts mains.

Features, specifications and appearance are subject to change without notice.

Declaration of Conformity

We, Harman Consumer Group International

2, route de Tours
72500 Chateau du Loir
France

declare in own responsibility that the products
described in this owner’s manual are in compliance
with technical standards:

EN 55013:2001 + A1:2003
EN 55020:2002 + A1:2003

Klaus Lebherz

Harman Consumer Group

International

Chateau du Loir, France 7/05

JBL Consumer Products 
250 Crossways Park Drive 
Woodbury, NY 11797 USA

JBL is a trademark of Harman International 
Industries, Incorporated, registered in the 
United States and/or other countries.

Part No. CSAMPOM7/05

• 200W RMS x 1 channel at 4 ohms and ≤1% THD + N
• Signal-to-noise ratio: 75dBA (reference 1W into 4 ohms)

• 300W RMS x 1 channel at 2 ohms, 14.4V supply and ≤1% THD + N
• Dynamic power: 460W at 2 ohms

• Effective damping factor: 6.395 at 4 ohms

• Frequency response: 10Hz – 300Hz (–3dB)

• Maximum input signal: 7,5V

• Maximum sensitivity: 100mV

• Output regulation: –0.07dB at 4 ohms

• Dimensions (L x W x H): 322 x 260 x 56mm (12-11/16" x 10-1/4" x 2-3/16")

• Fuses: 20A x 2

• 60W RMS x 4 channels at 4 ohms and ≤1% THD + N
• Signal-to-noise ratio: 75dBA (reference 1W into 4 ohms)

• 80W RMS x 4 channels at 2 ohms, 14.4V supply and ≤1% THD + N
• 160W RMS x 2 channels at 4 ohms, 14.4V supply and ≤1% THD + N
• Dynamic power: 145W at 2 ohms

• Effective damping factor: 6.395 at 4 ohms

• Frequency response: 10Hz – 27kHz (–3dB)

• Maximum input signal: 6V

• Maximum sensitivity: 100mV

• Output regulation: –0.03dB at 4 ohms

• Dimensions (L x W x H): 337 x 260 x 56mm (13-1/4" x 10-1/4" x 2-3/16")

• Fuses: 25A x 2

• 60W RMS x 2 channels at 4 ohms and ≤1% THD + N
• Signal-to-noise ratio: 75dBA (reference 1W into 4 ohms)

• 80W RMS x 2 channels at 2 ohms, 14.4V supply and ≤1% THD + N
• 160W RMS x 1 channel at 4 ohms, 14.4V supply and ≤1% THD + N
• Dynamic power: 160W at 2 ohms

• Effective damping factor: 6.395 at 4 ohms

• Frequency response: 10Hz – 27kHz (–3dB)

• Maximum input signal: 6V

• Maximum sensitivity: 100mV

• Output regulation: –0.03dB at 4 ohms

• Dimensions (L x W x H): 225 x 260 x 57mm

(8-7/8" x 10-1/4" x 2-1/4")

• Fuses: 25A x 1

This product is intended for mobile applications without connection to the 
110/230 volts mains.

Features, specifications and appearance are subject to change without notice.

Declaration of Conformity

We, Harman Consumer Group International

2, route de Tours
72500 Chateau du Loir
France

declare in own responsibility that the products
described in this owner’s manual are in compliance
with technical standards:

EN 55013:2001 + A1:2003
EN 55020:2002 + A1:2003

Klaus Lebherz

Harman Consumer Group

International

Chateau du Loir, France 7/05

JBL Consumer Products 
250 Crossways Park Drive 
Woodbury, NY 11797 USA

JBL is a trademark of Harman International 
Industries, Incorporated, registered in the 
United States and/or other countries.

Part No. CSAMPOM7/05

• 200W RMS x 1 channel at 4 ohms and ≤1% THD + N
• Signal-to-noise ratio: 75dBA (reference 1W into 4 ohms)

• 300W RMS x 1 channel at 2 ohms, 14.4V supply and ≤1% THD + N
• Dynamic power: 460W at 2 ohms

• Effective damping factor: 6.395 at 4 ohms

• Frequency response: 10Hz – 300Hz (–3dB)

• Maximum input signal: 7,5V

• Maximum sensitivity: 100mV

• Output regulation: –0.07dB at 4 ohms

• Dimensions (L x W x H): 322 x 260 x 56mm (12-11/16" x 10-1/4" x 2-3/16")

• Fuses: 20A x 2

• 60W RMS x 4 channels at 4 ohms and ≤1% THD + N
• Signal-to-noise ratio: 75dBA (reference 1W into 4 ohms)

• 80W RMS x 4 channels at 2 ohms, 14.4V supply and ≤1% THD + N
• 160W RMS x 2 channels at 4 ohms, 14.4V supply and ≤1% THD + N
• Dynamic power: 145W at 2 ohms

• Effective damping factor: 6.395 at 4 ohms

• Frequency response: 10Hz – 27kHz (–3dB)

• Maximum input signal: 6V

• Maximum sensitivity: 100mV

• Output regulation: –0.03dB at 4 ohms

• Dimensions (L x W x H): 337 x 260 x 56mm (13-1/4" x 10-1/4" x 2-3/16")

• Fuses: 25A x 2

• 60W RMS x 2 channels at 4 ohms and ≤1% THD + N
• Signal-to-noise ratio: 75dBA (reference 1W into 4 ohms)

• 80W RMS x 2 channels at 2 ohms, 14.4V supply and ≤1% THD + N
• 160W RMS x 1 channel at 4 ohms, 14.4V supply and ≤1% THD + N
• Dynamic power: 160W at 2 ohms

• Effective damping factor: 6.395 at 4 ohms

• Frequency response: 10Hz – 27kHz (–3dB)

• Maximum input signal: 6V

• Maximum sensitivity: 100mV

• Output regulation: –0.03dB at 4 ohms

• Dimensions (L x W x H): 225 x 260 x 57mm

(8-7/8" x 10-1/4" x 2-1/4")

• Fuses: 25A x 1

This product is intended for mobile applications without connection to the 
110/230 volts mains.

Features, specifications and appearance are subject to change without notice.