JBL CS60.2 (serv.man2) User Manual / Operation Manual ▷ View online
6
APPLICATIONS – CS60.2
Right
Left
Figure 9. CS60.2 used in 2-channel (stereo)
operation to drive a set of full-range speakers.
operation to drive a set of full-range speakers.
Figure 10. CS60.2 used in bridge mode to drive a
subwoofer.
subwoofer.
7
CONTROLS AND SETUP
SETTING THE
CROSSOVER(S)
Determine your system plans and set the
crossover mode switch accordingly.
If your system design does not include a
subwoofer with the CS60.4, set the
crossover mode to FLAT and skip to
“Setting Input Sensitivity”.
CROSSOVER(S)
Determine your system plans and set the
crossover mode switch accordingly.
If your system design does not include a
subwoofer with the CS60.4, set the
crossover mode to FLAT and skip to
“Setting Input Sensitivity”.
Initially set the crossover frequency
control midway. While listening to music,
adjust the crossover for the least perceived
distortion from the speakers, allowing them
to reproduce as much bass as possible.
control midway. While listening to music,
adjust the crossover for the least perceived
distortion from the speakers, allowing them
to reproduce as much bass as possible.
Systems using a separate subwoofer set
the crossover mode to HP (high pass) for
your full-range speakers. Adjust the
crossover frequency to limit bass and
provide increased system volume with less
distortion.
the crossover mode to HP (high pass) for
your full-range speakers. Adjust the
crossover frequency to limit bass and
provide increased system volume with less
distortion.
For subwoofers, choose the highest
frequency that removes vocal information
from the sound of the subwoofer.
frequency that removes vocal information
from the sound of the subwoofer.
If using the CS60.4 or CS60.2 to drive a
subwoofer(s), set the crossover mode to
LP (low pass).
subwoofer(s), set the crossover mode to
LP (low pass).
SETTING INPUT
SENSITIVITY
1. Initially turn the INPUT LEVEL control(s)
SENSITIVITY
1. Initially turn the INPUT LEVEL control(s)
to minimum (counter clockwise).
2. Reconnect the (–) negative lead to the
vehicle’s battery. Apply power to the
audio system and play a dynamic music
track.
audio system and play a dynamic music
track.
3. On the source unit, increase the volume
control to 3/4 volume. Slowly increase
the INPUT LEVEL control(s) toward three
o’clock until you hear slight distortion
in the music. Then reduce the INPUT
LEVEL slightly until distortion is no longer
heard.
the INPUT LEVEL control(s) toward three
o’clock until you hear slight distortion
in the music. Then reduce the INPUT
LEVEL slightly until distortion is no longer
heard.
NOTE: After the source unit is on, blue
LEDs (on the top panel) will light, indicating
the amplifier is on. If not, check the wiring,
especially the remote connection from
the source unit. Also refer to
“Troubleshooting” guide at right.
LEDs (on the top panel) will light, indicating
the amplifier is on. If not, check the wiring,
especially the remote connection from
the source unit. Also refer to
“Troubleshooting” guide at right.
SYMPTOM
LIKELY CAUSE
SOLUTION
No audio
No voltage at BATT+
Check voltages at
(POWER LEDs
or REM terminals,
amplifier terminals
are off)
or bad or no ground
with VOM
connection
No audio
Amplifier is
Make sure amplifier
(POWER
overheated
cooling is not blocked
LEDs are on)
at mounting location;
verify speaker-system
impedance is within
specified limits
verify speaker-system
impedance is within
specified limits
Voltage more than 16V
Check vehicle
or less than 8.5V on
charging system
BATT+ connection
No audio
Voltage less than 9V on
Check vehicle
(POWER BATT+
connection
charging
system
LEDs flash)
DC voltage on
Amplifier may need
amplifier output
service; see enclosed
warranty card for
service information
warranty card for
service information
Distorted audio
Input sensitivity is
Check INPUT
not set properly, or
LEVEL setting; or
amplifier or source
check speaker wires
unit is defective
for shorts or grounds
Distorted audio
Short circuit in
Remove speaker leads
and POWER
speaker or wire
one at a time to locate
LEDs flash
shorted speaker or
wire, then repair
wire, then repair
Music lacks
Speakers are not
Check speaker
“punch”
connected properly
connections for
proper polarity
proper polarity
TROUBLESHOOTING
Declaration of Conformity
We, Harman Consumer Group International
2, route de Tours
72500 Chateau du Loir
France
72500 Chateau du Loir
France
declare in own responsibility that the products
described in this owner’s manual are in compliance
with technical standards:
described in this owner’s manual are in compliance
with technical standards:
EN 55013:2001 + A1:2003
EN 55020:2002 + A1:2003
EN 55020:2002 + A1:2003
Klaus Lebherz
Harman Consumer Group
International
Chateau du Loir, France 7/05
JBL Consumer Products
250 Crossways Park Drive
Woodbury, NY 11797 USA
250 Crossways Park Drive
Woodbury, NY 11797 USA
JBL is a trademark of Harman International
Industries, Incorporated, registered in the
United States and/or other countries.
Industries, Incorporated, registered in the
United States and/or other countries.
Part No. CSAMPOM7/05
CS300.1
• 200W RMS x 1 channel at 4 ohms and ≤1% THD + N
• Signal-to-noise ratio: 75dBA (reference 1W into 4 ohms)
• Signal-to-noise ratio: 75dBA (reference 1W into 4 ohms)
• 300W RMS x 1 channel at 2 ohms, 14.4V supply and ≤1% THD + N
• Dynamic power: 460W at 2 ohms
• Dynamic power: 460W at 2 ohms
• Effective damping factor: 6.395 at 4 ohms
• Frequency response: 10Hz – 300Hz (–3dB)
• Maximum input signal: 7,5V
• Maximum sensitivity: 100mV
• Output regulation: –0.07dB at 4 ohms
• Dimensions (L x W x H): 322 x 260 x 56mm (12-11/16" x 10-1/4" x 2-3/16")
• Fuses: 20A x 2
CS60.4
• 60W RMS x 4 channels at 4 ohms and ≤1% THD + N
• Signal-to-noise ratio: 75dBA (reference 1W into 4 ohms)
• Signal-to-noise ratio: 75dBA (reference 1W into 4 ohms)
• 80W RMS x 4 channels at 2 ohms, 14.4V supply and ≤1% THD + N
• 160W RMS x 2 channels at 4 ohms, 14.4V supply and ≤1% THD + N
• Dynamic power: 145W at 2 ohms
• 160W RMS x 2 channels at 4 ohms, 14.4V supply and ≤1% THD + N
• Dynamic power: 145W at 2 ohms
• Effective damping factor: 6.395 at 4 ohms
• Frequency response: 10Hz – 27kHz (–3dB)
• Maximum input signal: 6V
• Maximum sensitivity: 100mV
• Output regulation: –0.03dB at 4 ohms
• Dimensions (L x W x H): 337 x 260 x 56mm (13-1/4" x 10-1/4" x 2-3/16")
• Fuses: 25A x 2
CS60.2
• 60W RMS x 2 channels at 4 ohms and ≤1% THD + N
• Signal-to-noise ratio: 75dBA (reference 1W into 4 ohms)
• Signal-to-noise ratio: 75dBA (reference 1W into 4 ohms)
• 80W RMS x 2 channels at 2 ohms, 14.4V supply and ≤1% THD + N
• 160W RMS x 1 channel at 4 ohms, 14.4V supply and ≤1% THD + N
• Dynamic power: 160W at 2 ohms
• 160W RMS x 1 channel at 4 ohms, 14.4V supply and ≤1% THD + N
• Dynamic power: 160W at 2 ohms
• Effective damping factor: 6.395 at 4 ohms
• Frequency response: 10Hz – 27kHz (–3dB)
• Maximum input signal: 6V
• Maximum sensitivity: 100mV
• Output regulation: –0.03dB at 4 ohms
• Dimensions (L x W x H): 225 x 260 x 57mm
(8-7/8" x 10-1/4" x 2-1/4")
• Fuses: 25A x 1
SPECIFICATIONS
www.jbl.com
This product is intended for mobile applications without connection to the
110/230 volts mains.
110/230 volts mains.
Features, specifications and appearance are subject to change without notice.
Declaration of Conformity
We, Harman Consumer Group International
2, route de Tours
72500 Chateau du Loir
France
72500 Chateau du Loir
France
declare in own responsibility that the products
described in this owner’s manual are in compliance
with technical standards:
described in this owner’s manual are in compliance
with technical standards:
EN 55013:2001 + A1:2003
EN 55020:2002 + A1:2003
EN 55020:2002 + A1:2003
Klaus Lebherz
Harman Consumer Group
International
Chateau du Loir, France 7/05
JBL Consumer Products
250 Crossways Park Drive
Woodbury, NY 11797 USA
250 Crossways Park Drive
Woodbury, NY 11797 USA
JBL is a trademark of Harman International
Industries, Incorporated, registered in the
United States and/or other countries.
Industries, Incorporated, registered in the
United States and/or other countries.
Part No. CSAMPOM7/05
CS300.1
• 200W RMS x 1 channel at 4 ohms and ≤1% THD + N
• Signal-to-noise ratio: 75dBA (reference 1W into 4 ohms)
• Signal-to-noise ratio: 75dBA (reference 1W into 4 ohms)
• 300W RMS x 1 channel at 2 ohms, 14.4V supply and ≤1% THD + N
• Dynamic power: 460W at 2 ohms
• Dynamic power: 460W at 2 ohms
• Effective damping factor: 6.395 at 4 ohms
• Frequency response: 10Hz – 300Hz (–3dB)
• Maximum input signal: 7,5V
• Maximum sensitivity: 100mV
• Output regulation: –0.07dB at 4 ohms
• Dimensions (L x W x H): 322 x 260 x 56mm (12-11/16" x 10-1/4" x 2-3/16")
• Fuses: 20A x 2
CS60.4
• 60W RMS x 4 channels at 4 ohms and ≤1% THD + N
• Signal-to-noise ratio: 75dBA (reference 1W into 4 ohms)
• Signal-to-noise ratio: 75dBA (reference 1W into 4 ohms)
• 80W RMS x 4 channels at 2 ohms, 14.4V supply and ≤1% THD + N
• 160W RMS x 2 channels at 4 ohms, 14.4V supply and ≤1% THD + N
• Dynamic power: 145W at 2 ohms
• 160W RMS x 2 channels at 4 ohms, 14.4V supply and ≤1% THD + N
• Dynamic power: 145W at 2 ohms
• Effective damping factor: 6.395 at 4 ohms
• Frequency response: 10Hz – 27kHz (–3dB)
• Maximum input signal: 6V
• Maximum sensitivity: 100mV
• Output regulation: –0.03dB at 4 ohms
• Dimensions (L x W x H): 337 x 260 x 56mm (13-1/4" x 10-1/4" x 2-3/16")
• Fuses: 25A x 2
CS60.2
• 60W RMS x 2 channels at 4 ohms and ≤1% THD + N
• Signal-to-noise ratio: 75dBA (reference 1W into 4 ohms)
• Signal-to-noise ratio: 75dBA (reference 1W into 4 ohms)
• 80W RMS x 2 channels at 2 ohms, 14.4V supply and ≤1% THD + N
• 160W RMS x 1 channel at 4 ohms, 14.4V supply and ≤1% THD + N
• Dynamic power: 160W at 2 ohms
• 160W RMS x 1 channel at 4 ohms, 14.4V supply and ≤1% THD + N
• Dynamic power: 160W at 2 ohms
• Effective damping factor: 6.395 at 4 ohms
• Frequency response: 10Hz – 27kHz (–3dB)
• Maximum input signal: 6V
• Maximum sensitivity: 100mV
• Output regulation: –0.03dB at 4 ohms
• Dimensions (L x W x H): 225 x 260 x 57mm
(8-7/8" x 10-1/4" x 2-1/4")
• Fuses: 25A x 1
SPECIFICATIONS
www.jbl.com
This product is intended for mobile applications without connection to the
110/230 volts mains.
110/230 volts mains.
Features, specifications and appearance are subject to change without notice.
Display