DOWNLOAD JBL CS60.2 (serv.man2) Service Manual ↓ Size: 479.51 KB | Pages: 8 in PDF or view online for FREE

Model
CS60.2 (serv.man2)
Pages
8
Size
479.51 KB
Type
PDF
Document
User Manual / Operation Manual
Brand
Device
Car Audio
File
cs602-sm2.pdf
Date

JBL CS60.2 (serv.man2) User Manual / Operation Manual ▷ View online

CS300.1
CS60.4
CS60.2
CAR AUDIO 
POWER AMPLIFIER
OWNER’S MANUAL
www.jbl.com
The Official Brand of Live Music.
®
English
INSTALLATION 
2
THANK YOU 
for purchasing a JBL CS Series amplifier. 
In order that we may better serve you
should you require warranty service for
your new amplifier, please retain your 
original purchase receipt and return the
enclosed warranty registration card.
WARNING
Playing loud music in an automobile can
hinder your ability to hear traffic and
permanently damage your hearing. We
recommend listening at low or moderate
levels while driving your car. JBL accepts
no liability for hearing loss, bodily injury or
property damage resulting from the use or
misuse of this product.
IMPORTANT
To get the best performance from your 
JBL CS Series amplifiers, we strongly
recommend that installation be entrusted
to a qualified professional. Although these
instructions explain how to install 
CS amplifiers in a general sense, they do
not show specific installation methods that
may be required for your particular vehicle.
If you do not have the necessary tools or
experience, do not attempt the installation
yourself. Instead, please ask your 
authorized JBL car audio dealer about 
professional installation.
INSTALLATION 
WARNINGS AND TIPS
•  Always wear protective eyewear when
using tools.
• Turn off the audio system and other 
electrical devices before you start.
Disconnect the (–) negative lead from
your vehicle’s battery.
•  Check clearances on both sides of a
planned mounting surface before drilling
any holes or installing any screws.
Remember that the screws can extend
behind the surface.
•  At the installation sites, locate and make
a note of all fuel lines, hydraulic brake
lines, vacuum lines and electrical wiring.
Use extreme caution when cutting or
drilling in and around these areas.
•  Before drilling or cutting holes, use a
utility knife to remove unwanted fabric or
vinyl to keep material from snagging in a
drill bit.
•  When routing cables, keep input-signal
cables away from power cables and
speaker wires.
•  When making connections, make 
certain they are secure and properly
insulated.
• If the amplifier’s fuse must be replaced,
use only the same type and rating as that
of the original. Do not substitute another
kind.
CHOOSING A LOCATION
AND MOUNTING THE
AMPLIFIER
Choose a mounting location in the trunk 
or cargo area where the amplifier will not
be damaged by shifting cargo. Amplifier
cooling is essential for proper amplifier
operation. If the amplifier is to be installed
in an enclosed space, make sure there is
sufficient air circulation for the amplifier 
to cool itself.
When mounting the amplifier under a seat,
ensure that it is clear of all moving seat
parts and does not affect the seat
adjustments. Mount the amplifier so it is not 
damaged by the feet of backseat 
passengers. Make sure that the amplifier is
mounted securely using nuts and bolts or
the supplied mounting screws.
Mount the amplifier so that it remains 
dry – never mount an amplifier outside the
vehicle or in the engine compartment.
3
INSTALLATION 
POWER CONNECTIONS
The CS amplifiers are capable of delivering
extremely high power levels, and require a
heavy-duty and reliable connection to the
vehicle’s electrical system in order to
perform optimally. See Figures 1, 2 and 3 for
connection location. Please adhere to the
following instructions carefully:
Ground Connection
Connect the amplifier’s Ground (GND)
terminal to a solid point on the vehicle’s
metal chassis, as close to the amplifier 
as possible. Refer to the chart below to
determine minimum wire-gauge size.
Scrape away any paint from this location;
use a star-type-lock washer to secure the
connection.
Power Connection
Connect a wire (see chart at right for
appropriate gauge) directly to the vehicle’s
positive battery terminal, and install an
appropriate fuse holder within 50cm (18") of
the battery terminal. 
Do not install the fuse
at this time.
Route the wire to the
amplifier’s location, and connect it to the
amplifier’s Positive (+12V) terminal. Be sure
to use appropriate grommets whenever
routing wires through the firewall or other
sheet metal. 
Failure to adequately protect
the positive wire from potential damage
may result in a vehicle fire.
When you are
done routing and connecting this wire, you
may install the fuse at the battery.
Remote Connection
Connect the amplifier’s Remote (REM) 
terminal to the source unit’s Remote Turn-
On lead using a minimum of 1mm
2
wire.
NOTE: If your source unit does not have a
remote turn-on connection, connect the
amplifier’s (REM) terminal to the vehicle’s
accessory circuit.
Speaker Connections
Refer to the application guides on the
pages that follow. Speaker connections
should be made using a minimum of 
2.5mm
2
wire.
Wire Gauge Chart
Amplifier
Maximum
Minimum 
Model
Current Draw
Wire Gauge
CS60.2
22A 8,4 
mm
CS60.4
40A 8,4 
mm
CS300.1
42A 8,4 
mm
These recommendations assume 1,5m à
2,5m wire runs. If your installation differs
markedly, you will need to adjust the wire
gauge accordingly.
Figure 1. Terminal connection end plate for CS300.1
Figure 3. Terminal connection end plate for CS60.4.
Figure 2. Terminal connection end plate for CS60.2.
4
APPLICATIONS – CS300.1
The CS subwoofer amplifiers are 
single-channel amplifiers. There are
two sets of terminals to make it easy 
to connect multiple woofers. Either 
set of (+/–) terminals may be used when
connecting woofers.
To the right are two application 
diagrams to help plan your subwoofer
system installation. Figures 4 and 5
show how to configure the CS300.1
subwoofer amplifiers.
NOTE: For simplicity, Figures 4 and 5
do not show power, remote and input
connections.
NOTE: Minimum speaker load is 
2 ohms.
Figure 4. CS subwoofer amplifier
with two woofers connected.
Figure 5. CS subwoofer amplifier
with one woofer connected.
Page of 8
Display

JBL CS60.2 (serv.man2) User Manual / Operation Manual ▷ Download

  • DOWNLOAD JBL CS60.2 (serv.man2) Service Manual ↓ Size: 479.51 KB | Pages: 8 in PDF or view online for FREE
  • Here you can View online or download the User Manual / Operation Manual for the JBL CS60.2 (serv.man2) in PDF for free, which will help you to disassemble, recover, fix and repair JBL CS60.2 (serv.man2) Car Audio. Information contained in JBL CS60.2 (serv.man2) User Manual / Operation Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.