DOWNLOAD JBL WBN 26 Service Manual ↓ Size: 60.61 KB | Pages: 1 in PDF or view online for FREE

Model
WBN 26
Pages
1 Few pages! See other manuals at the bottom of the first or last page.
Size
60.61 KB
Type
PDF
Document
User Manual / Operation Manual
Brand
Device
Audio
File
wbn-26.pdf
Date

JBL WBN 26 User Manual / Operation Manual ▷ View online

IMPORTANT SAFETY NOTE: PROPER SELECTION OF MOUNTING
HARDWARE NOT INCLUDED HEREIN AND PROPER ASSEMBLY AND
INSTALLATION OF BRACKETS, INCLUDING BUT NOT LIMITED TO
SELECTION OF APPROPRIATE WEIGHT BEARING SUPPORT AND
BRACKET USE WITH THE SPECIFIED SPEAKER ONLY IS THE
EXCLUSIVE RESPONSIBILITY OF THE CUSTOMER.  MANUFACTURER
DISCLAIMS ANY LIABILITY FOR THE SELECTION OF MOUNTING
HARDWARE AND/OR BRACKET INSTALLATION.
a. Remove the nut (9) and the split washer (8) if necessary. Fully
insert the threaded portion (1) of the ‘thick’ end of the ball/shaft (2) into
the center opening (6) of the housing bracket (7), with the housing bracket
middle ‘convex’ area towards the threaded portion (1).
b. Engage, and using a suitable wrench, securely tighten the split
washer (8) and the nut (9) with the split washer (8) sandwiched between the
‘convex’ area on the back of the housing bracket (7) and the nut (9).
c. Place the housing bracket (7) against the housing (10) of the
speaker. The housing bracket (7) features an arrow and the word ‘UP’
indicating the correct installation direction of the bracket.
d. Using a suitable screw driver securely tighten all three bolts (11)
to the back of the housing. If the bracket (7) is installed correctly, it
will be sitting flush against the back of the housing.
e. The back-up cord (13) is provided as an additional measure to
prevent the fall of the speaker in the event the speaker becomes detached
from the wall bracket. The remaining bracket-to-housing bolt (12) (bolts 11
and 12 are identical) will need to go through the eyelet (14) (eyelets 14
and 15 are also the same) at the end of the cord before going through the
housing (10). Using a suitable screwdriver, tighten this bolt (12) also to
the speaker housing (10).
f. Using the wall bracket (16) as a template, mark the screw locations
for where the unit is to be mounted. DO NOT MOUNT THE BRACKET TO
THE WALL UNTIL STEP (i). The wall bracket (16) is to be mounted onto a
wood stud on the wall, using #12, minimum 1 inch long, pan head wood
screws. Make sure that all 4 screws are driven into the stud and not in
drywall. If the bracket needs to be mounted on drywall, the use of
properly selected and installed wall-anchors and screws is essential.
Make sure that the screw head is at least 0.41 inches (approximately 7/16
inches) or larger in diameter so that it can properly hold the backup cord
eyelet (15).
g. Remove the nut (19) and the split washer (18) if necessary. Fully
insert the threaded portion (3) of the ‘thin’ end of the ball/shaft (2) into
the center opening (17) of the wall bracket (16), with the wall bracket
middle area towards the threaded portion (3).
h. Engage, and using a suitable wrench, securely tighten the split
washer (18) and the nut (19), with the split washer (18) sandwiched between
the area on the back of the wall bracket (16) and the nut (19).
i. Mount the wall bracket (16) onto the wall, using three of the four
#12 screws (20) (not supplied), while following the recommendations in item
(f) above. Two of the three screws should be used in the top two holes of
the mounting bracket. The third screw is used in one of the wall bracket’s
(16) lower screw holes. Install the fourth #12 screw (20) making sure that
it goes through the eyelet (15) at the end of the back-up cord (13) before
it goes through the wall bracket’s other lower screw hole. Using a suitable
screwdriver, securely tighten all 4 screws.
j. Using a suitable wrench, loosen the small nut (4) and the large nut
(5) on the ball shaft (2) to allow the orientation of the speaker. Once the
correct orientation is obtained fully tighten the large nut (5) with a
suitable wrench until the ball/shaft (2) is locked into position and does
not move. Tighten the small nut (4) with another wrench while keeping the
large nut (5) tight using the first wrench. Double-check and make sure both
nuts (4 and 5) are fully tightened and that the speaker is stable on the
bracket. The two nuts (4 and 5) should now be fully locked into position,
and completely tightened against each other.
Display

JBL WBN 26 User Manual / Operation Manual ▷ Download

  • DOWNLOAD JBL WBN 26 Service Manual ↓ Size: 60.61 KB | Pages: 1 in PDF or view online for FREE
  • Here you can View online or download the User Manual / Operation Manual for the JBL WBN 26 in PDF for free, which will help you to disassemble, recover, fix and repair JBL WBN 26 Audio. Information contained in JBL WBN 26 User Manual / Operation Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.