JBL TLX CSS-SP1000 SAT (LR1000) (serv.man2) User Manual / Operation Manual ▷ View online
– +
+ –
– +
– +
+ –
+ –
+ –
Receiver
Subwoofer
Right
Surround
Left
Surround
Right Front
Left Front
Center
Right
Front
Front
Right
Surround
Left
Front
Left
Surround
Speaker-Level Input
(from amplifier)
Right Left
Speaker-Level Output
(to external speakers)
(to external speakers)
+ –
Center
Speaker
+
–
+
–
+
–
+
–
two.
Speaker Connections
Separate and strip the ends of
the speaker wire as shown.
Speakers and electronics ter-
minals have corresponding (+)
and (–) terminals. It is impor-
tant to connect both speakers
the speaker wire as shown.
Speakers and electronics ter-
minals have corresponding (+)
and (–) terminals. It is impor-
tant to connect both speakers
identically: (+) on the speaker
to (+) on the amplifier and (–)
on the speaker to (–) on the
amplifier. Wiring “out of phase”
results in thin sound, weak
bass and a poor stereo image.
to (+) on the amplifier and (–)
on the speaker to (–) on the
amplifier. Wiring “out of phase”
results in thin sound, weak
bass and a poor stereo image.
Connection Tips
Speaker level
TLX CSS-SP1000 OM 7/17/98 4:39 PM Page 5
three.
Operation
min max
Volume
min max
Volume
Mode
Procedure
LED Status
Off
Receiver/amplifier off
Off
On
Receiver/amplifier on and playing program material
Green
Standby
Simply turn off your receiver/amplifier. The subwoofer will
Red
turn off after approximately five minutes. The subwoofer
will turn on when your receiver/amplifier begins playing again.
will turn on when your receiver/amplifier begins playing again.
Volume
Crossover Frequency
The crossover-frequency knob
determines the highest fre-
quency your subwoofer will
reproduce. It allows a seam-
less transition from the
subwoofer to the satellite
speakers. Experiment with
determines the highest fre-
quency your subwoofer will
reproduce. It allows a seam-
less transition from the
subwoofer to the satellite
speakers. Experiment with
this adjustment to find the
crossover frequency that
sounds best with your
speakers. When using the
speaker-level connections,
the crossover adjustment will
also limit the low frequencies
crossover frequency that
sounds best with your
speakers. When using the
speaker-level connections,
the crossover adjustment will
also limit the low frequencies
being sent to your satellite
speakers. This means that
your satellites won’t have
to try and reproduce the
information the subwoofer
is playing.
speakers. This means that
your satellites won’t have
to try and reproduce the
information the subwoofer
is playing.
TLX CSS-SP1000 OM 7/17/98 4:39 PM Page 6
If there is no sound from
any of the speakers, check
the following:
any of the speakers, check
the following:
• Receiver/amplifier is on and
a source is playing.
• Powered subwoofer is
plugged in and is in the “On”
position.
• Check all wires and con-
nections between receiver/
amplifier and speakers. Make
sure all wires are connected.
Make sure none of the speaker
wires are frayed, cut or
punctured.
• Review proper operation of
your receiver/amplifier.
a source is playing.
• Powered subwoofer is
plugged in and is in the “On”
position.
• Check all wires and con-
nections between receiver/
amplifier and speakers. Make
sure all wires are connected.
Make sure none of the speaker
wires are frayed, cut or
punctured.
• Review proper operation of
your receiver/amplifier.
If there is no sound coming
from one speaker, check the
following:
from one speaker, check the
following:
• Check the “Balance” control
on your receiver/amplifier.
• Check all wires and con-
nections between receiver/
amplifier and speakers. Make
sure all wires are connected.
on your receiver/amplifier.
• Check all wires and con-
nections between receiver/
amplifier and speakers. Make
sure all wires are connected.
Make sure none of the
speaker wires are frayed, cut
or punctured.
speaker wires are frayed, cut
or punctured.
If the system plays at low
volumes but shuts off as
volume is increased, check
the following:
volumes but shuts off as
volume is increased, check
the following:
• Check all wires and con-
nections between receiver/
amplifier and speakers. Make
sure all wires are connected.
Make sure none of the
speaker wires are frayed, cut
or punctured.
• If more than one pair of
main speakers is being used,
check the minimum imped-
ance requirements of your
receiver/amplifier.
nections between receiver/
amplifier and speakers. Make
sure all wires are connected.
Make sure none of the
speaker wires are frayed, cut
or punctured.
• If more than one pair of
main speakers is being used,
check the minimum imped-
ance requirements of your
receiver/amplifier.
If there is low bass output,
check the following:
check the following:
• Make sure the connections
to the left and right “Speaker
Inputs” have the correct
polarity (+ and –).
to the left and right “Speaker
Inputs” have the correct
polarity (+ and –).
• Make sure that the sub-
woofer is plugged into an
active electrical outlet.
• Powered subwoofer is
plugged in and is in the “On”
position.
woofer is plugged into an
active electrical outlet.
• Powered subwoofer is
plugged in and is in the “On”
position.
If there is no sound from
the surround speakers,
check the following:
the surround speakers,
check the following:
• Check all wires and con-
nections between receiver/
amplifier and speakers. Make
sure all wires are connected.
Make sure none of the
speaker wires are frayed, cut
or punctured.
• Review proper operation of
your receiver/amplifier and its
surround-sound features.
• Make sure the movie or TV
show you are watching is
recorded in Dolby* surround.
If it is not, check to see if
your receiver/amplifier has
other surround modes you
may use.
nections between receiver/
amplifier and speakers. Make
sure all wires are connected.
Make sure none of the
speaker wires are frayed, cut
or punctured.
• Review proper operation of
your receiver/amplifier and its
surround-sound features.
• Make sure the movie or TV
show you are watching is
recorded in Dolby* surround.
If it is not, check to see if
your receiver/amplifier has
other surround modes you
may use.
Troubleshooting
TLX CSS-SP1000 OM 7/17/98 4:39 PM Page 7
©
1998 JBL, Incorporated.
JBL and Home Cinema are trademarks of JBL, Incorporated.
*Trademark of Dolby Laboratories.
Printed in USA 3/98
*Trademark of Dolby Laboratories.
Printed in USA 3/98
Part No. TLXCSS-SP1000OM
C
E
L E
B R A T I N
G
5
0
Y E A
R
S
A Harman International Company
TLX CSS-SP1000
System
Frequency Response
45Hz – 20kHz (
45Hz – 20kHz (
±
3dB)
Left and Right
Speakers
Recommended Power
10 – 70 watts
Frequency Response
75Hz – 20kHz (
10 – 70 watts
Frequency Response
75Hz – 20kHz (
–
6dB)
Nominal Impedance
8 ohms
Sensitivity
88dB @ 1 watt/1 meter
Crossover Frequency
3kHz (midrange to tweeter)
Tweeter
One 10mm titanium-laminate
dome, video shielded
Midrange
One 5-1/4"
Dimensions (H x W x D)
11 x 6-1/2 x 7-1/4 inches
279 x 165 x 184mm
Weight
7 lbs/3.2 kg
8 ohms
Sensitivity
88dB @ 1 watt/1 meter
Crossover Frequency
3kHz (midrange to tweeter)
Tweeter
One 10mm titanium-laminate
dome, video shielded
Midrange
One 5-1/4"
Dimensions (H x W x D)
11 x 6-1/2 x 7-1/4 inches
279 x 165 x 184mm
Weight
7 lbs/3.2 kg
Center Channel
Recommended Power
10 – 100 watts
Frequency Response
90Hz – 20kHz (
10 – 100 watts
Frequency Response
90Hz – 20kHz (
–
6dB)
Nominal Impedance
8 ohms
Sensitivity
90dB @ 1 watt/1 meter
Crossover Frequency
7.5kHz (midrange to tweeter)
Tweeter
One 10mm titanium-laminate
dome, video shielded
Midrange
Dual 4-1/2", video shielded
Dimensions (H x W x D)
6-1/2 x 18-1/2 x 6-1/8 inches
165 x 470 x 156mm
Weight
10 lbs/4.5 kg
8 ohms
Sensitivity
90dB @ 1 watt/1 meter
Crossover Frequency
7.5kHz (midrange to tweeter)
Tweeter
One 10mm titanium-laminate
dome, video shielded
Midrange
Dual 4-1/2", video shielded
Dimensions (H x W x D)
6-1/2 x 18-1/2 x 6-1/8 inches
165 x 470 x 156mm
Weight
10 lbs/4.5 kg
Surrounds
Recommended Power
10 – 35 watts
Frequency Response
120Hz – 16kHz (
10 – 35 watts
Frequency Response
120Hz – 16kHz (
–
6dB)
Nominal Impedance
8 ohms
Sensitivity
87dB @ 1 watt/1 meter
Dimensions (H x W x D)
6 x 6-3/8 x 5-1/2 inches
152 x 162 x 140mm
Weight
3 lbs/1.4 kg
8 ohms
Sensitivity
87dB @ 1 watt/1 meter
Dimensions (H x W x D)
6 x 6-3/8 x 5-1/2 inches
152 x 162 x 140mm
Weight
3 lbs/1.4 kg
Subwoofer
Amplifier
75 watts RMS
Frequency Response
45Hz – 150Hz (
75 watts RMS
Frequency Response
45Hz – 150Hz (
–
6dB)
Crossover Frequency
50Hz – 200Hz
(continuously variable)
Woofer
8" bass reflex
Dimensions (H x W x D)
13-1/2 x 14-3/4 x 15-1/8 inches
343 x 375 x 384mm
Weight
26 lbs/ 11.8 kg
50Hz – 200Hz
(continuously variable)
Woofer
8" bass reflex
Dimensions (H x W x D)
13-1/2 x 14-3/4 x 15-1/8 inches
343 x 375 x 384mm
Weight
26 lbs/ 11.8 kg
Specifications
Refinements may be made on occasion to existing products
without notice, but will always meet or exceed original specifi-
cations unless otherwise stated.
without notice, but will always meet or exceed original specifi-
cations unless otherwise stated.
TLX CSS-SP1000 OM 7/17/98 4:39 PM Page 8
Display
