JBL SUB 150P (serv.man2) Service Manual ▷ View online
tuRning the subwoofeR on and off
Set the subwoofer’s Power Switch to the “On” position. The subwoofer will
Set the subwoofer’s Power Switch to the “On” position. The subwoofer will
automatically turn itself on when it receives an audio signal, and it will go
into Standby mode after it has received no audio signal for approximately
10 minutes. The subwoofer’s LED will glow green when the subwoofer is
on and will glow red when the subwoofer is in Standby.
If you will not be using the subwoofer for an extended period – for
instance, if you’re going on vacation – set the Power Switch to the “Off”
position.
subwoofeR adJustments: cRossoveR contRol
NOTE: The Crossover control functions only
NOTE: The Crossover control functions only
when the Input Mode switch is in the “Normal”
position.
The Crossover control adjusts the subwoofer’s
built-in low-pass filter crossover between
50Hz and 200Hz. The higher you set the
Crossover control, the higher in frequency the
subwoofer will operate and the more its bass will “overlap” that of the
satellite speakers. This adjustment helps achieve a smooth transition of
bass frequencies between the subwoofer and the satellites for a variety of
different rooms and subwoofer locations.
To set the Crossover control, listen for the smoothness of the bass. If
the bass seems too strong at certain frequencies, try a lower Crossover
control setting. If the bass seems too weak at certain frequencies, try a
higher Crossover control setting.
subwoofeR adJustments: volume
Use the Level control to set the subwoofer’s
Use the Level control to set the subwoofer’s
volume. Turn the knob clockwise to increase
the subwoofer’s volume; turn the knob
counterclockwise to decrease the volume. Once
you have balanced the subwoofer’s volume
with that of the other speakers in your system,
you shouldn’t have to change the Level control
setting.
Notes on Setting Subwoofer Volume:
• Sometimes the ideal subwoofer volume setting for music is too loud
for films, while the ideal setting for films is too quiet for music. When
setting the subwoofer volume, listen to both music and films with
strong bass content and find a “middle ground” volume level that
works for both.
• If your subwoofer always seems too loud or too quiet, you may want
to place it in a different location. Placing the subwoofer in a corner will
tend to increase its bass output, while placing it away from any walls
or corners will tend to lessen its bass output.
subwoofeR adJustments: Phase
The Phase switch determines whether the subwoofer
The Phase switch determines whether the subwoofer
driver’s piston-like action moves in and out in phase
with the satellite speakers. If the subwoofer were to
play out of phase with the satellite speakers, the sound
waves from the satellites could partially cancel out the
waves from the subwoofer, reducing bass performance
and sonic impact. This phenomenon depends in part on the placement of
all the speakers relative to each other in the room.
Although in most cases you should leave the Phase switch in the “Normal”
position, there is no absolutely correct setting for the Phase switch. When
the subwoofer is properly in phase with the satellite speakers, the sound
will be clearer and have maximum impact, and percussive sounds like
drums, piano and plucked strings will sound more lifelike. The best way
to set the Phase switch is to listen to music that you know well and to set
the switch in the position that gives drums and other percussive sounds
maximum impact.
sPecIFIcatIons
oPeratIng the suBwooFer
is a trademark of HARMAN International Industries, Incorporated.
Features, specifications and appearance are subject to change without notice.
Part No. 950-0328-001
Features, specifications and appearance are subject to change without notice.
Part No. 950-0328-001
HARMAN Consumer, Inc.
www.jbl.com
Low-frequency
transducer:
10" (250mm) PolyPlas cone (down-firing)
Enclosure type:
Ported (down-firing)
Amplifier power:
300 watts (RMS); 500 watts (peak)
Frequency response:
27Hz – 150Hz (–3dB)
Audio controls:
Volume level, crossover frequency, phase
Connections:
RCA line-level and LFE inputs
Power requirement:
120V, 60Hz (US); 220V – 230V, 50Hz/60Hz
(EU)
Power consumption:
<1W (0.040A @ 230V) standby;
320W (1.8A @ 230V) peak
<6W (0.06A @ 120V) standby;
320W (3.2A @ 120V) peak
Dimensions (W x H x D):
17-3/8" x 18-1/2" x 17-3/8"
(441mm x 470mm x 441mm)
Weight:
39.7 lb (18.0kg)
0242CSK - JBL SUB150P OM_v3.indd 4
29/09/10 9:57:52
JBL
SUB 150P/230 Service Manual
Page 5 of 47
JBL
SUB 150P/230 Service Manual
Page 6 of 47
SUB150P/230 Troubleshooting flow charts
yes
Stand-by BD check
+6V,-6V, Stand-by
VOL.
no
no
yes
yes
no
yes
no
yes
no
yes
no
yes
no
yes
no
no
yes
yes
no
.
Start
Dc voltage check
±Vcc,±15V
OK
Check transformer
C
168,
C
169
,D
123
,
D
124,
C
170
Power on check
LED red &blue
OK
Check vol module
& connector
cable& ±15V.ect
Check THD output
power, noise
OK
Check pre board
& power board ,
±Vcc,±15V ect
Test frequency
Response
OK
Check U
102
,R
124
,
C
104,
R
125
,C
117
.ect
Test input sensitivity
OK
Check U
101
,R
117,
R
112,
R
114
ect
Test protection
OK
Check U
107
.R
237
±15Vcc ect
Test limiter circuit
OK
Check U
106
.Q
107
ect
Auto off Function
Hi pot test
OK
Check U
103
.Q
101.
Q
102
.C
131.
R
142
;Ac
cord, Transformer.
OK
Listening test
OK
The Amp ass’y ok
END
Test phase sw,low
pass sw rabos vr
Check sw103,102,
R158,163,177 ect
JBL
SUB 150P/230 Service Manual
Page 7 of 47
Part Number
Description
Qty
25PR12FZL-DW04-E
10" woofer
1
010-7620-05320-E
200W AMP
1
241-100-05560-0BAE
Cabinet assembly
1
315-ABS-05277-0BAE
top trim plate
1
316-AL-05412-0VAE
logo
1
320-SR-05238-0BAE
rubber feet
4
321-ABS-05145-0BAE
plastic feet
4
333-EVA-06049-0BAE
EVA
4
350-AM04020D079-E
screw T4*20
26
350-AM04036D084-E
screw T4*36
1
402-000-06475-E
beauty carton
1
430-002-05444-E
pearl bag
1
431-000-07286-E
top EPE
1
431-000-07287-E
bottom EPE
1
370-000-05068-E
RCA cable
1
249-HIPS-05372-0BAE
port tube
1
327-010-05055-0BAE
grille cup
4
328-SPG-05936-0WAE
damping material 255*255*20mm
1
328-SPG-05937-0WAE
damping material 300*360*20mm
2
328-SPG-05938-0WAE
damping material 300*380*20mm
1
Part Number
Description
Qty
ref.
123-11K4DRH-E Ferrite core K4DRH 16*28.5*9 (RoHS)
1
150-R0905507-E transformer 230V/50Hz 300W3PIN 3.96HOUSING RoHS
1
152-V60201A01-E power cord VDE 6.0FT 2PIN
1
153-VPST101S2-E INLET SOCKET PRONIC (RoHS)
1
154-V20006T0-E fuse 2.0A 250V 20mm VDE(RoHS)
1
155-620R345A-E fuse holder UL/CSA 5*20mm R3-45A(RoHS)
1
156-H200050-E
shrink tube 20Φ 50mm (RoHS)
1
156-H220050-E
shrink tube 22ψ 50mm (RoHS)
1
156-H300040-E
shrink tube ψ30*40mm (RoHS)
1
156-H700090-E
shrink tube Φ70MM*90MM(RoHS)
1
162-10121002-E WIRE UL1617 120mm BRN 20#(RoHS)
1
162-10126001-E WIRE UL1617 120mm BLU 20#(RoHS)
2
162-5016D001-E WIRE 24# 160mm
1
162-5020D029-E WIRE UL1617 18AWG 200mm BLU&BRN
1
162-A050D006-E wire UL1015 18AWG R/B
1
163-11009-E
plastic tie 100mm
6
163-11809-E
tie 180mm*3.6
2
180-P3024DB-E ROCKER 3024-DB
1
193-0S4211-E
INSULATION SPACER 42*11 (RoHS)
1
193-201612TR-E INSULATION SPACER T0-220 16mm*12mm(RoHS)
3
236-AL-05001-0LAE AL bar (RoHS)
1
302-AL-05310-1BAE rear panel 313.81*300*2.5
1
306-ABS-05079-0BAE rear enclosure 198*298*102H
1
311-ABS-00028-0BAE knob 46077-W P.V.C.(RoHS)
2
323-AL-05000-0LAE heat sink (RoHS)
1
325-FE-00400-0LAE PCB bracket 58*9*13.5T (RoHS)
1
333-EVA-00188-0BAE EVA 170x5x1t
1
333-EVA-00220-0BAE EVA 225*15*1t UL(RoHS)
1
333-EVA-00866-0BAE EVA 48*18*1.5T (RoHS)
1
333-SPG-00863-0BAE foam 100*50*5T (RoHS)
1
335-NYL-00002-0BAE wire clip 4K-4 NO-BB(RoHS)
1
336-RUB-05103-0BAE RUB gasket 97*16*3.0T
2
350-EM04012D024-E 4¢*12 screw
4
351-AM03006A069-E M3*6 screw
3
010-7620-05320-E
AMP JBL STUDIO SUB150P/230 200W 0.5W STAND-BY(RoHS)
MODEL NAME: SUB150P/230
JBL
SUB 150P/230 Service Manual
Page 8 of 47
Click on the first or last page to see other SUB 150P (serv.man2) service manuals if exist.