JBL S 50 User Manual / Operation Manual ▷ View online
thank you
for choosing JBL. For over 50 years, JBL
has been involved in every aspect of musical and film recording
and reproduction, from live performances to monitoring the
recordings you play in your home, car or office.
We’re confident that the
JBL loudspeakers
you have
chosen will provide every note of enjoyment that you expected –
and that when you think about purchasing additional audio
equipment for your home, car or office, you will once again
choose JBL.
Please take a moment to complete the enclosed profile card.
It enables us to keep you posted on our latest advancements,
and helps us to better understand our customers and to build
products that meet their needs and expectations.
JBL Consumer Products
S50
simple
setup guide
setup guide
S50 Owner’s Manual 7/20/98 11:50 AM Page 1
one.
Speaker Placement
Proper placement of the
speakers is an important
step in obtaining the
most realistic soundstage
possible. These recom-
mendations are for the
optimum placement of the
speakers is an important
step in obtaining the
most realistic soundstage
possible. These recom-
mendations are for the
optimum placement of the
loudspeakers. Use these
placement recommenda-
tions as a guide. Slight
variations will not
diminish your listening
pleasure.
placement recommenda-
tions as a guide. Slight
variations will not
diminish your listening
pleasure.
The S50 loudspeakers are
video shielded and can
be safely placed near a
television.
video shielded and can
be safely placed near a
television.
As Front Speakers
As Surround Speakers
5–6 ft.
S50
40–60
o
o
S50 Owner’s Manual 7/20/98 11:50 AM Page 2
two.
Speaker Connections
Connection Tips
– +
– +
– +
– +
Speaker Outputs
RIGHT LEFT
RIGHT
LEFT
Speakers and electronics terminals have corresponding
(+) and (–) terminals. It is important to connect both
speakers identically: (+) on the speaker to (+) on the
amplifier and (–) on the speaker to (–) on the amplifier.
Wiring “out of phase” results in thin sound, weak bass
and a poor stereo image.
(+) and (–) terminals. It is important to connect both
speakers identically: (+) on the speaker to (+) on the
amplifier and (–) on the speaker to (–) on the amplifier.
Wiring “out of phase” results in thin sound, weak bass
and a poor stereo image.
Troubleshooting
If there is no sound from
any of the speakers,
check the following:
any of the speakers,
check the following:
• Receiver/amplifier is on
and a source is playing.
• Review proper operation
of your receiver/amplifier.
and a source is playing.
• Review proper operation
of your receiver/amplifier.
If there is no sound
coming from one
speaker, check the
following:
coming from one
speaker, check the
following:
• Check the “Balance”
control on your receiver/
amplifier.
• Check all wires and
connections between
receiver/amplifier and
speakers.
• Make sure all wires are
connected. Make sure none
of the speaker wires are
frayed, cut or punctured.
control on your receiver/
amplifier.
• Check all wires and
connections between
receiver/amplifier and
speakers.
• Make sure all wires are
connected. Make sure none
of the speaker wires are
frayed, cut or punctured.
If the system plays at
low volumes but shuts
off as volume is
increased, check the
following:
low volumes but shuts
off as volume is
increased, check the
following:
• Check all wires and con-
nections between receiver/
amplifier and speakers.
• Make sure all wires are
connected. Make sure none
of the speaker wires are
frayed, cut or punctured.
• If more than one pair of
main speakers is being
used, check the minimum
impedance requirements of
your receiver/amplifier.
nections between receiver/
amplifier and speakers.
• Make sure all wires are
connected. Make sure none
of the speaker wires are
frayed, cut or punctured.
• If more than one pair of
main speakers is being
used, check the minimum
impedance requirements of
your receiver/amplifier.
If there is low bass out-
put, check the following:
put, check the following:
• Make sure the polarities
(+ and –) of the left and
right “Speaker Inputs” are
connected properly.
(+ and –) of the left and
right “Speaker Inputs” are
connected properly.
S50 Owner’s Manual 7/20/98 11:50 AM Page 3
Declaration of Conformity
Kongevejen 194B
DK-3460 Birkerød
DENMARK
DK-3460 Birkerød
DENMARK
declare in own responsibility, that the loudspeakers
described in this owner’s manual are in compliance with
technical standards:
EN 50 081-1/1992
EN 50 082-1/3.1995
Steen Michaelsen
Birkerød. DENMARK. 11/97
C
E
L E
B R A T I N
G
5
0
Y E A
R
S
©
1997 JBL, Incorporated. JBL is a registered
trademark of JBL, Incorporated.
11/97
Part No. S50OM
A Harman International Company
Specifications
S50
Frequency Response
45Hz – 20kHz (–6dB)
80Hz – 18kHz (±2dB)
Sensitivity
86dB @ 2.83 volts/1 meter
Recommended Maximum Amplifier Power*
100 watts
Nominal Impedance
8 ohms
Crossover Frequency
2300Hz
Low-Frequency Transducer
5-1/4"
High-Frequency Transducer
1" soft dome with Bi-Radial® horn
Dimensions (H x W x D)
13-5/8 x 6-7/8 x 10"
346 x 175 x 254mm
Weight
14 lbs/6.4 kg
45Hz – 20kHz (–6dB)
80Hz – 18kHz (±2dB)
Sensitivity
86dB @ 2.83 volts/1 meter
Recommended Maximum Amplifier Power*
100 watts
Nominal Impedance
8 ohms
Crossover Frequency
2300Hz
Low-Frequency Transducer
5-1/4"
High-Frequency Transducer
1" soft dome with Bi-Radial® horn
Dimensions (H x W x D)
13-5/8 x 6-7/8 x 10"
346 x 175 x 254mm
Weight
14 lbs/6.4 kg
Occasional refinements
may be made to existing
products without notice,
but will always meet
or exceed original
specifications unless
otherwise stated.
may be made to existing
products without notice,
but will always meet
or exceed original
specifications unless
otherwise stated.
*The maximum recom-
mended amplifier power
rating will ensure proper
system headroom to allow
for occasional peaks. We
do not recommend sus-
tained operation at these
maximum power levels.
mended amplifier power
rating will ensure proper
system headroom to allow
for occasional peaks. We
do not recommend sus-
tained operation at these
maximum power levels.
S50 Owner’s Manual 7/20/98 11:51 AM Page 4
Display