DOWNLOAD JBL PSW-D110 Service Manual ↓ Size: 1.96 MB | Pages: 28 in PDF or view online for FREE

Model
PSW-D110
Pages
28
Size
1.96 MB
Type
PDF
Document
Service Manual
Brand
Device
Audio
File
psw-d110.pdf
Date

JBL PSW-D110 Service Manual ▷ View online

JBL Consumer Products Inc.
250 Crossways Park Drive
Woodbury, N.Y. 11797
1-800-336-4JBL in the USA
A Harman International Company
Rev C 8/2000
PSW-D110/DPS-10
Powered Subwoofer
SERVICE MANUAL
SAFETY INFORMATION
Warning
Any person performing service of this unit will be exposed to
hazardous voltages and the risk of electric shock. It is
assumed that any person who removes the amplifier from
this cabinet has been properly trained in protecting against
avoidable injury and shock. Therefore, any service
procedures are to be performed by qualified service
personal ONLY!
Caution
This unit does not have a power switch. Hazardous
voltages are present within the unit whenever it is
plugged in.
Before the amplifier is plugged in, be sure its rated voltage
corresponds to the voltage of the AC power source to be
used. Incorrect voltage could cause damage to the
amplifier when the AC power cord is plugged in. Do not
exceed rated voltage by more than 10%: operation below
90% of rated voltage will cause poor performance or may
shut the unit off.
Leakage/Resistance Check
Before returning the unit to the customer, perform a leakage
or resistance test as follows:
Leakage Current. Note there is no power switch on this unit.
When the power plug is plugged in, the unit is live. Connect
the unit to its rated power source. Using an ammeter,
measure the current between the neutral side of the AC
supply and chassis ground of the unit under test. if leakage
current exceeds 0.5mA, the unit is defective. Reverse the
polarity of the AC supply and repeat.
Resistance. Measure the resistance from either side of the
line cord to chassis ground. If it is less than 500k ohms, the
unit is defective.
WARNING! DO NOT return the unit to the customer if it fails
one of these tests until the problem is located and corrected.
Critical Components
All components identified with the IEC symbol
in the parts list and the schematic diagram
designate components in which safety can be
of special significance when replacing a
component identified with
. Use only the
replacement parts designated in the parts list or parts with
the same rating of resistance, wattage or voltage.
List of Safety Components Requiring
Exact Replacements
F1
Fuse SLO BLO 1.25A 250V UL approved
PWRCORD SPT-2 or better with polarized plug, UL
approved wired with the hot side to fused
side. Use with factory replacement panel
strain relief only.
TRX1
Transformer. Use only factory replacement.
DBR
Bridge diode. Use only factory replacement.
C1, 2
4700uF, 50V electrolytic filter caps. Be sure
replacement part is at least the same
working voltage and capacitance rating.
Also the lead spacing is important.
Incorrect spacing may cause premature
failure due to internal cabinet pressure and
vibration.
C6
10uF 50V electrolytic radial
See Page 14 Service Bulletin
S52AMI
Power output module. Use only factory
replacement
Faceplate
Faceplate. Use only factory replacement
Air leak cover Use only factory replacement
CMC1
Use only factory replacement
L1
Use only factory replacement
Fuse PCB
Use only factory replacement
Main PCB
Use only factory replacement
2
Amplifier/Subwoofer
PSW-D110/DPS-10
3
Amplifier/Subwoofer
PSW-D110/DPS-10
TABLE OF CONTENTS
SAFETY INFORMATION ...............................................2
TABLE OF CONTENTS.................................................3
GENERAL SPECIFICATIONS .......................................3
DETAILED SPECIFICATIONS.......................................4
PSW-D110/DPS-10 CONTROLS AND
THEIR FUNCTION .........................................................6
OPERATION...................................................................7
SPEAKER CONNECTIONS...........................................8
TROUBLESHOOTING ...................................................9
PSW-D110/DPS-10 TEST SET UP
AND PROCEDURE......................................................10
PSW-D110/DPS-10 POWER AMP
TEST PROCEDURE and FLOW CHART....................11
SERVICE BULLETIN JBL9902 REV1 - MAY 1999 ..........14
SERVICE BULLETIN JBL9903 - APRIL 1999 ..................15
SERVICE BULLETIN JBL2000-01 - JANUARY 2000.......16
CABINET EXPLODED VIEWS ....................................17
AMPLIFIER EXPLODED VIEW ...................................18
PSW-D110/DPS-10 MECHANICAL PARTS LIST.......19
PACKING EXPLODED VIEWS....................................20
PSW-D110/DPS-10 Version 3.53 PCB
(Component Side) ........................................................21
PSW-D110/DPS-10 Version 3.53 PCB
(Solder Side) ................................................................22
PSW-D110/DPS-10 Version 3.93 PCB
(Component Side) ........................................................23
PSW-D110/DPS-10 Version 3.93 PCB
(Solder Side) ................................................................24
PSW-D110/DPS-10 ELECTRICAL PARTS LIST ........25
PSW-D110/DPS-10 INTEGRATED CIRCUITS ...........26
PWS-D110/DPS-10 SCHEMATIC 1 of 2.....................27
PWS-D110/DPS-10 SCHEMATIC 2 of 2.....................28
GENERAL SPECIFICATIONS
Amplifier Power (RMS). . . . . . . . 150 watts
Driver 10" . . . . . . . . . . . . . High-Polymer Laminate
Inputs . . . . . . . . . . . . . . . Line Level and Speaker Level
Outputs . . . . . . . . . . . . . . Line Level and Speaker Level
Low-Pass Frequency . . . . . . . . Continuously variable from 60Hz – 180Hz
High-Pass Frequency . . . . . . . . Continuously variable from 60Hz – 180Hz
when using line-level inputs
180Hz when using speaker-level inputs
Frequency Response . . . . . . . . 30Hz – low-pass crossover setting
PSW-D110
DPS10
Dimensions (H x W x D) . . . . . . . 15-3/8 x 15-3/8 x 17"
18-1/16 x 14-7/8 x 15-7/8"
(391 x 391 x 432mm)
(459 x 378 x 403mm)
Weight . . . . . . . . . . . . . . . 33 lbs/15 kg
30 lbs/13.6 kg
DETAILED SPECIFICATIONS
LINE VOLTAGE
Yes/No
Hi/Lo Line
Unit
Notes
US 120vac/60Hz
Yes
108-132
Vrms
Normal Operation
EU 230vac/50-60Hz
Yes
207-264
Vrms
Normal operation, MOMS required
Parameter
Specification Unit
Conditions
Notes
Amp Section
Type (Class AB, D, other)
D
Class D Preferred...Sink required for Class AB
Load
Impedance
(speaker)
4
Ohms
Nominal
Z-curve required
Rated Output Power
150
Watts
1 input driven
Peak power
75
Watts
1 input driven
RMS
THD@ Rated Power
0.1
%
22k filter
75w (Power Bandwidth 30-100Hz)
THD @ 1 Watt
0.1
%
22k filter
DC Offset
2
mV-DC
@ Speaker Outputs
Damping factor
>200
DF
Input Sensitivity
Input Frequency
50
Hz
Nominal Freq.
1 input driven
Line Input
110
mVrms
To Rated Power/ Vol @ Max
1 input driven
Speaker/Hi Level Input
2.7
Vrms
To Rated Power/ Vol @ Max
1 input driven: AP source Z = 25 ohms
Signal to Noise
SNR-A-Weighted
100
dBA
relative to 75w power
A-Weighting filter
SNR-unweighted
75
dBr
relative to 75w power
22k filter
SNR rel. 1W-unweighted
65
dBr
relative to 1W Output
22k filter
Residual Noise Floor
2
mVrms
Volume @max, using RMS reading DMM/VOM (or A/P)
Residual Noise Floor
1.5
mVrms(max)
Volume @max, w/ A/P Swept Bandpass Measurement (Line freq.+ harmonics)
Input Impedance
Line Input
10k
ohms
Nominal
Speaker/Hi Level Input
200
ohms
Nominal
Filters
0dBr = 1w @ 50Hz
Low Pass (fixed or
variable)
Variable
Low Pass filter (point or
range)
60-120
Hz
-3dB Point
Slope
18
dB/Octave
Q
1
Damping
Subsonic filter (HPF)
25
Hz
-3dB Point
Slope
12
dB/Octave
Q
1
Damping
4
Amplifier/Subwoofer
PSW-D110/DPS-10
Page of 28
Display

JBL PSW-D110 Service Manual ▷ Download

  • DOWNLOAD JBL PSW-D110 Service Manual ↓ Size: 1.96 MB | Pages: 28 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the JBL PSW-D110 in PDF for free, which will help you to disassemble, recover, fix and repair JBL PSW-D110 Audio. Information contained in JBL PSW-D110 Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.