JBL ON TOUR (serv.man8) EMC - CB Certificate ▷ View online
- Page 1 of 17 -
Order No. 23172
TEST REPORT
IEC 60950, 3rd Edition, 1999
Product
Computer Speaker system
Name and address of the
applicant
applicant
Name and address of the
manufacturer
manufacturer
Name and address of the
factory
factory
Harman (Suzhou) Electronics Co, LTD.
3, Jinshan Road,
Suzhou New District
Jiangsu Province
China, 215011
3, Jinshan Road,
Suzhou New District
Jiangsu Province
China, 215011
Rating and principal
characteristics
characteristics
1 A, 6 VDC
SELV
SELV
Class of equipment
Class III equipment
Trade mark
Model/type
On Tour
Serial no
Prototype
Tested according to
IEC 60950, 3rd Edition, 1999
Safety of information technology equipment
Name and address of the
testing laboratory
testing laboratory
11696 Sorrento Valley Road, suite F
San Diego, CA 92121 USA
San Diego, CA 92121 USA
Telephone
+1 (858) 755-
5525
Fax
+1 (858) 452-
1810
+1 (858) 755-
5525
Fax
+1 (858) 452-
1810
Tested by
14 May 2004
Signature
Date
Manuel E. Ugalde
Name in block letters
Verified by
14 May 2004
Signature
Date
Thomas Landrey
Name in block letters
The content of this TRF fully covers the original TRF published by FIMKO. This form is only for use by Nemko, or by others
according to special agreement with Nemko. The completed test report is not valid for external use, unless issued by Nemko or
attached to a Nemko certification document. The report shall not be reproduced without written permission from Nemko and may
then only be copied in full.
Issue Nemko 2001-01
- Page 2 of 17 -
Order No. 23172
Additional tests according to:
Common Modifications, Special National Conditions and
National Deviations
National Deviations
EN 60950: 2000.
Common Modifications, Special National Conditions
and National Deviations. (See Appendix EN 60950:
2000; confer countries indicated under additional
information).
Common Modifications, Special National Conditions
and National Deviations. (See Appendix EN 60950:
2000; confer countries indicated under additional
information).
Other requirements
Country listed in CB Bulletin No. 105A, dated May 2003
as follows: Singapore (SG)
as follows: Singapore (SG)
All country deviations listed in the CB Bulletin are
covered by the Common Modifications, Special
National Conditions, National Deviations, and National
Requirements noted above except for the following
countries which are documented in Country Deviation
Appendix’s attached to this report:
covered by the Common Modifications, Special
National Conditions, National Deviations, and National
Requirements noted above except for the following
countries which are documented in Country Deviation
Appendix’s attached to this report:
Australia (including New Ze aland): CB Bulletin No.
105A, dated May 2003.
Canada: CB Bulletin No. 105A, dated May 2003.
105A, dated May 2003.
Canada: CB Bulletin No. 105A, dated May 2003.
China: CB Bulletin No. 105A, dated May 2003.
Israel: CB Bulletin No. 105A, dated May 2003.
Japan: CB Bulletin No. 105A, dated May 2003.
Republic of Korea: CB Bulletin No. 105A, dated May
2003.
2003.
Singapore: CB Bulletin No. SS237, dated 2001.
United States: CB Bulletin No. 105A, dated May 2003.
General remarks:
The test results presented in this report relate only to the object tested.
This report shall not be reproduced except in full without the written approval of the testing laboratory.
Possible test case verdicts:
The test results presented in this report relate only to the object tested.
This report shall not be reproduced except in full without the written approval of the testing laboratory.
Possible test case verdicts:
P = Pass, F = Fail, N = Not applicable, — = No verdict required. Placed in the column to the right (Verdict).
- Page 3 of 17 -
Order No. 23172
SUMMARY OF TESTING :
Sub-clause
Information/Remarks
Comments
1.2.02.01
Normal load as described in Annex L or as close
as possible to the most severe normal use
as possible to the most severe normal use
Normal operation is considered 1/8
th
of maximum
undistorted. Non-clipping was determined using a
1 KHz sinusoidal signal input. For maximum
normal operation, 1/8
1 KHz sinusoidal signal input. For maximum
normal operation, 1/8
th
of the non-clipping
amplitude was used with a filtered pink noise input
signal.
signal.
1.7.1
Required markings regarding supply.
Class III Equipment with an enclosure made of
HB-Material, using a non-special connector for the
DC input must have a marking stating the
manufacturer and model number of the power
supply to be used.
HB-Material, using a non-special connector for the
DC input must have a marking stating the
manufacturer and model number of the power
supply to be used.
1.7.14
Language of safety markings /instruction.
Instructions and equipment marking related to
safety shall be applied in a language, which is
acceptable in the country in which the equipment
is to be sold.
safety shall be applied in a language, which is
acceptable in the country in which the equipment
is to be sold.
3.2
Connection to the supply.
Unit is powered by a limited power source
complying with Sub-clause 2.11. Connection is
made by a detachable power supply cord with a
non-special type connector. The external power
supply was not evaluated in this test report.
complying with Sub-clause 2.11. Connection is
made by a detachable power supply cord with a
non-special type connector. The external power
supply was not evaluated in this test report.
- Page 4 of 17 -
Order No. 23172
ADDITIONAL INFORMATION
The subject equipment is a computer stereo system powered by a detachable Limited Power Source
with a non-specialized type connector or 4 AA Batteries.
with a non-specialized type connector or 4 AA Batteries.
Equipment mobility: Moveable Equipment intended for tabletop use.
Connection to the supply: Class III equipment, not directly connected to mains.
Circuit characteristics: Secondary Circuits, powered by external Limited Power Source
Weight: 0.5 kg.
Dimensions: 171mm X 89mm X 38mm
Maximum recommended ambient (Tmra): 25°C
NAME AND ADDRESS OF PRODUCTION -SITES (FACTORIES):
See page 1.
INFORMATION ABOUT THE STANDARDS / DOCUMENTS CONSIDERED
IEC 60950, 3
rd
Edition: 1999
EN 60950, 3
r d
Edition: 2000