JBL ON CALL (serv.man2) EMC - CB Certificate ▷ View online
Page 2 of 99 ST-06153
TRF No.: IECEN60950_1A
Particulars: test item vs. test requirements
Equipment mobility ..................................... : Direct plug-in
Operating condition ..................................... : Continuous
Mains supply tolerance (%) ......................... : + 6 %, + 10 % and – 10 % (the test voltage + 10 % is
Equipment mobility ..................................... : Direct plug-in
Operating condition ..................................... : Continuous
Mains supply tolerance (%) ......................... : + 6 %, + 10 % and – 10 % (the test voltage + 10 % is
required by the manufacturer)
Tested for IT power systems ...................... : Yes
IT testing, phase-phase voltage (V) ........... : 230 V for Norway
Class of equipment ..................................... : Class II
Mass of equipment (kg) ............................... : Max. 0.11 kg
Protection against ingress of water ............ : IP20
Test case verdicts
IT testing, phase-phase voltage (V) ........... : 230 V for Norway
Class of equipment ..................................... : Class II
Mass of equipment (kg) ............................... : Max. 0.11 kg
Protection against ingress of water ............ : IP20
Test case verdicts
Test case does not apply to the test object : N/A (Not Applicable)
Test item does meet the requirement ......... : P (Pass)
Test item does not meet the requirement ... : F (Fail)
Testing
Test item does meet the requirement ......... : P (Pass)
Test item does not meet the requirement ... : F (Fail)
Testing
Date of receipt of test item .......................... : May 12, 2006
Date(s) of performance of test .................... : May 12, 2006 – May 17, 2006
General remarks
“This report is not valid as a CB Test Report unless appended by an approved CB Testing
Laboratory and appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02”.
The test result presented in this report relate only to the object(s) tested.
This report shall not be reproduced, except in full, without the written approval of the Issuing testing
laboratory.
“(see Appendix #)” refers to additional information appended to the report.
“(see appended table #)” refers to a table appended to the report.
Throughout this report a comma (point) is used as the decimal separator.
Additional information
Additional special deviations of CN (China) of IEC 60950, 3rd ed. are checked.
Date(s) of performance of test .................... : May 12, 2006 – May 17, 2006
General remarks
“This report is not valid as a CB Test Report unless appended by an approved CB Testing
Laboratory and appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02”.
The test result presented in this report relate only to the object(s) tested.
This report shall not be reproduced, except in full, without the written approval of the Issuing testing
laboratory.
“(see Appendix #)” refers to additional information appended to the report.
“(see appended table #)” refers to a table appended to the report.
Throughout this report a comma (point) is used as the decimal separator.
Additional information
Additional special deviations of CN (China) of IEC 60950, 3rd ed. are checked.
Page 3 of 99 ST-06153
TRF No.: IECEN60950_1A
Copy of marking plate and summary of test results (information/comments):
(Representative)
I.T.E. POWER SUPPLY
Model No.: MU15-C033280-C5
Input: 100-240 V
Model No.: MU15-C033280-C5
Input: 100-240 V
50/60 Hz 0.5 A
Output: 3.3 V
2.8 A
LEI
I.T.E. POWER SUPPLY
Model No.: MU15-C060250-C5
Input: 100-240 V
50/60 Hz 0.5 A
Output: 6 V
2.5 A
LEI
I.T.E. POWER SUPPLY
Model No.: MU15-C240010-C5
Input: 100-240 V
50/60 Hz 0.5 A
Output: 24 V
0.1 A
LEI
I.T.E. POWER SUPPLY
Model No.: MU15-C033280-C5
Input: 100-240 V
50/60 Hz 0.5 A
Output: 3.3 V
2.8 A
LEI
I.T.E. POWER SUPPLY
Model No.: MU15-C060250-C5
Input: 100-240 V
Model No.: MU15-C060250-C5
Input: 100-240 V
50/60 Hz 0.5 A
Output: 6 V
2.5 A
LEI
I.T.E. POWER SUPPLY
Model No.: MU15-C240010-C5
Input: 100-240 V
Model No.: MU15-C240010-C5
Input: 100-240 V
50/60 Hz 0.5 A
Output: 24 V
0.1 A
LEI
Page 4 of 99 ST-06153
TRF No.: IECEN60950_1A
Summary of testing:
1.6.2 Input current test
1.7.13 Marking durability test
2.1.1.1 b Finger test
2.1.1.1 c Pin test
2.1.1.5 Energy hazards test
2.1.1.7 Stored Discharge on capacitor test
2.2.2 Voltages under normal conditions test
2.2.3 Voltages under fault conditions test
2.4 Limited current circuits test
2.5 Limited power sources test
2.9.2 Humidity conditioning test
2.10.2 Determination of working voltage test
2.10.3, 2.10.4 Clearances and creepage distances measurements
2.10.5 Distance through insulation measurements
4.2.2 Mechanical strength – steady force test, 10 N
4.2.4 Mechanical strength – steady force test, 250 N
4.2.6 Mechanical strength – drop test
4.2.7 Mechanical strength – stress relief test
4.3.6 Strain on socket-outlet test (for direct plug-in equipment)
4.5.1 Normal operating test
4.5.2 Ball pressure test
5.1 Touch current test
5.2 Electric strength test
5.3 Abnormal operating and fault conditions test
General product information:
Explanation of model designation of MU15-C******-**:
The 1
st
to 3
rd
“*” denotes the output voltage, which can be “033” (3.3 Vdc) to “240” (24 Vdc).
The 4
th
to 6
th
“*” denotes the output current, which can be “010” (0.1 A) to “280” (2.8 A).
The 7
th
to 8
th
“*” denotes the type of plug, which can be “A1”, “A2”, “A3”, “A4”, “B2”, “C4” or “C5” (“A1”
comply with ANSI/UL 1310 and ANSI/UL 1681, “A2” comply with GB 1002-1996, “A3” comply with
AS/NZS 3112: 2004, “A4” comply with IRAM 2063, “B2” comply with BS 1363, “C4” comply with KSC
8305, and “C5” comply with EN 50075 and IEC 60884-1).
AS/NZS 3112: 2004, “A4” comply with IRAM 2063, “B2” comply with BS 1363, “C4” comply with KSC
8305, and “C5” comply with EN 50075 and IEC 60884-1).
