JBL ON BEAT AWAKE (serv.man3) Service Manual ▷ View online
4
JBL is a trademark of HARMAN International Industries, Incorporated, registered in the
United States and/or other countries.
JBL OnBeat is a trademark of HARMAN International Industries, Incorporated.
The Bluetooth word mark and logo are registered trademarks and are owned by the Bluetooth SIG, Inc., and any use
The Bluetooth word mark and logo are registered trademarks and are owned by the Bluetooth SIG, Inc., and any use
of such marks by HARMAN International Industries, Incorporated, is under license.
iPhone, iPod, iPod touch and iPad are trademarks of Apple Inc., registered in the U.S. and other countries. iPod,
iPhone and iPad not included. “Made for iPod,” “Made for iPhone” and “Made for iPad” mean that an electronic
accessory has been designed to connect specifically to iPod or iPhone or iPad, respectively, and has been certified
by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its
compliance with safety and regulatory standards. Please note that the use of this accessory with iPod, iPhone, or iPad
may affect wireless performance.
Features, specifications and appearance are subject to change without notice.
Part No. 920-0762-001 Rev. A
Features, specifications and appearance are subject to change without notice.
Part No. 920-0762-001 Rev. A
HARMAN International Industries, Incorporated
SettInGS
Clock brightness: You can adjust the brightness of the clock readout to one of three
settings (Bright, Medium, Dim) by pressing the Snooze button while the OnBeat aWake is
on, but no audio is playing through it.
Clock format: Press and hold the Snooze button to cycle the clock between the 12-hour
and 24-hour format.
UPGRaDInG FIRmWaRe
You can upgrade the OnBeat aWake’s firmware from within the JBL Amp-Up App that is
installed on a docked device.
Visit www.jbl.com to download the JBL Amp-Up App and the JBL Musicflow App.
Hereby, [HARMAN International Industries, Incorporated], declares that this JBL ONBEAT AWAKE is in compliance with
the essential requirements and other relevant provisions of Directive 1999/5/EC, ErP 2009/125/EC Directive and RoHS
2011/65/EU Directive. The declaration of conformity may be consulted at the support section on our Web site, accessible
from www.jbl.com.
FCC STATEMENT
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION: EXPOSURE TO RADIO FREQUENCY RADIATION
To comply with FCC RF exposure compliance requirements, this device must not be co-located or operating
in conjunction with any other antenna or transmitter.
CAUTION: Changes or modifications not expressly approved in writing by HARMAN International may void the user’s
authority to operate this equipment.
JBL
AWAKE and RIZE Service Manual
Page 4 of 43
5-1 Trouble shooting Chart
LEDS are not bright
NG
LEDS are not bright
Go
NG
OK
Check U2 Pin1/3(5V) and Pin 5(3.3V) on
the main board
Replace U2 on the main
board
NG
OK
OK
Replace the U2 on the
LED board
Fix the 8PIN FFC
Check the 8PIN FFC connector
Check the SPI between the U5 and U2 on
the LED board.
the LED board.
Replace U5 on the main board
JBL
AWAKE and RIZE Service Manual
Page 5 of 43
5-2 Trouble shooting Chart
Ipad no authentication
Ipad no authentication
Go
OK
Check the 24pin FFC connector
NG
Replace the connector
NG
OK
Check the IIC between U5 and U6
Check the 30PIN DOCK, move ipad in a
little scope and check the authentication is
OK or NG.
little scope and check the authentication is
OK or NG.
Replace the dock board
JBL
AWAKE and RIZE Service Manual
Page 6 of 43
5-3 Trouble shooting Chart
Bluetooth no connection
Bluetooth no
connection
Go
OK
Weld it once more
NG
Check the +3.3V net on the main
board and fix it
NG
OK
Replace the BT module
Check the weld of the BT module
Check power supply
Q13 and FB12(3.3V)
JBL
AWAKE and RIZE Service Manual
Page 7 of 43
Click on the first or last page to see other ON BEAT AWAKE (serv.man3) service manuals if exist.