JBL JSR 675 User Manual / Operation Manual ▷ View online
8
1. FM INDOOR ANTENNA
Connect the supplied antenna (the
wire lead) to a 300
wire lead) to a 300
Ω
/75
Ω
adapter
and connect the adapter to the 75
Ω
FM antenna terminal, as shown in the
Rear Panel Connection Diagram.
Change the position of the antenna
until you get the best reception of
your favorite stations.
Rear Panel Connection Diagram.
Change the position of the antenna
until you get the best reception of
your favorite stations.
2. FM OUTDOOR
ANTENNA
ANTENNA
An outdoor FM antenna may be used
to further improve the quality of
reception. Disconnect the indoor
antenna before replacing it with the
outdoor one. A 75
to further improve the quality of
reception. Disconnect the indoor
antenna before replacing it with the
outdoor one. A 75
Ω
/300
Ω
adapter
must be used.
3. AM LOOP ANTENNA
Tune in your favorite AM station and
position the loop antenna for best
reception. Try other stations and find
the position that gives the best overall
reception. When this unit is mounted
in a rack or placed on a shelf with
insufficient space behind, hang the
antenna on a wall in the direction
which gives the best reception.
position the loop antenna for best
reception. Try other stations and find
the position that gives the best overall
reception. When this unit is mounted
in a rack or placed on a shelf with
insufficient space behind, hang the
antenna on a wall in the direction
which gives the best reception.
NOTE:
If noise is heard during AM
reception, move the antenna for bet-
ter reception. To prevent undesired
noise, the AM LOOP ANTENNA
should be located at least 12 inches
(30 cm) away from the remote control
wires.
ter reception. To prevent undesired
noise, the AM LOOP ANTENNA
should be located at least 12 inches
(30 cm) away from the remote control
wires.
4. SYSTEM GROUND
TERMINAL
TERMINAL
To reduce hum to a minimum, connect
the ground lead from your turntable to
this terminal.
the ground lead from your turntable to
this terminal.
5. PHONO INPUT JACKS
Input for a TURNTABLE with an MM
cartridge requiring a 47K ohm of load
impedance. Connect shielded cables
from your phono to the LEFT and
RIGHT input jacks.
cartridge requiring a 47K ohm of load
impedance. Connect shielded cables
from your phono to the LEFT and
RIGHT input jacks.
NOTE:
Do not place your
TURNTABLE on a speaker enclosure.
This will avoid howling caused by
transmission of the speaker vibration
to the TURNTABLE.
This will avoid howling caused by
transmission of the speaker vibration
to the TURNTABLE.
6. TV/AUX INPUT JACKS
This extra stereo input is provided for
any source you want to hear. An
additional compact disc player, a
tape recorder, a video cassette
recorder (VCR) etc., can be plugged
into these jacks.
any source you want to hear. An
additional compact disc player, a
tape recorder, a video cassette
recorder (VCR) etc., can be plugged
into these jacks.
7. CD INPUT JACKS
Connect the output cables of a
compact disc player to these jacks.
compact disc player to these jacks.
8. TAPE 1 PLAY JACKS
Connect the line output of your
CASSETTE DECK to these jacks.
CASSETTE DECK to these jacks.
9. TAPE 1 REC JACKS
Connect the line input of your
CASSETTE DECK to these jacks.
CASSETTE DECK to these jacks.
10. TAPE 2 MONITOR
PLAY JACKS
PLAY JACKS
Connect the line output of your
CASSETTE DECK to these jacks. This
input may be connected to the line
output of the audio processor like an
optional graphic equalizer or a Digital
Signal Processor.
CASSETTE DECK to these jacks. This
input may be connected to the line
output of the audio processor like an
optional graphic equalizer or a Digital
Signal Processor.
11. TAPE 2 MONITOR REC
JACKS
JACKS
Connect the line input of your
CASSETTE DECK to these jacks. EQ
controls, loudness and volume settings
have no effect on the signal from this
output for recording. To monitor this
input source while recording, press the
TAPE 2 MON button (MONITOR ON
position). These REC jacks may be
used for the line input of the audio
processor like an optional graphic
equalizer or a Digital Signal Processor.
CASSETTE DECK to these jacks. EQ
controls, loudness and volume settings
have no effect on the signal from this
output for recording. To monitor this
input source while recording, press the
TAPE 2 MON button (MONITOR ON
position). These REC jacks may be
used for the line input of the audio
processor like an optional graphic
equalizer or a Digital Signal Processor.
AM LOOP ANTENNA SETTING
Stand and place it on a shelf
or hang it on a wall.
or hang it on a wall.
LEG
Rear Panel Connections
JSR675 OM (230V) 7/28/98 10:08 AM Page 10
9
12. VIDEO/AUDIO INPUT
(PLAY) JACKS OF VCR 1
(PLAY) JACKS OF VCR 1
Connect these jacks to the corre-
sponding AUDIO OUTPUT jacks of
your VCR.
sponding AUDIO OUTPUT jacks of
your VCR.
13. VIDEO/AUDIO OUTPUT
(REC) JACKS OF VCR 1
(REC) JACKS OF VCR 1
Connect these jacks to the corre-
sponding INPUT jacks of a VCR.
VIDEO OUTPUT jack: Connect this
jack to the VIDEO INPUT jack of the
VCR. AUDIO REC jack: Connect
these jacks to the AUDIO INPUT
jacks of the VCR.
sponding INPUT jacks of a VCR.
VIDEO OUTPUT jack: Connect this
jack to the VIDEO INPUT jack of the
VCR. AUDIO REC jack: Connect
these jacks to the AUDIO INPUT
jacks of the VCR.
14. VIDEO/AUDIO INPUT
(PLAY) JACKS OF VCR 2
(PLAY) JACKS OF VCR 2
Connect these jacks to the corre-
sponding OUTPUT jacks of your VCR
or VDP.
sponding OUTPUT jacks of your VCR
or VDP.
15. VIDEO MONITOR JACK
Connect this jack to the VIDEO
INPUT jack of a TV/MONITOR.
INPUT jack of a TV/MONITOR.
16. REMOTE OUT JACK
Connect this jack to the REMOTE IN
jack on a Harman Kardon component.
Use one of the accessory mini-plug
cables.
jack on a Harman Kardon component.
Use one of the accessory mini-plug
cables.
You can control some Harman Kardon
components in your system using the
JSR675 remote commander.
components in your system using the
JSR675 remote commander.
17. MULTI-ROOM REMOTE
IN JACK
IN JACK
Connect a remote IR sensor to this
jack. You can operate the unit by
remote commander through the
adapter. It is convenient when the unit
is located in a separate room. (See
page 10)
jack. You can operate the unit by
remote commander through the
adapter. It is convenient when the unit
is located in a separate room. (See
page 10)
18. FRONT, CENTER, REAR
PRE OUT AND MAIN IN
JACKS
PRE OUT AND MAIN IN
JACKS
FRONT PRE OUT
When a separate power amplifier is
used to drive the front speakers,
connect the power amplifier input to
these jacks.
used to drive the front speakers,
connect the power amplifier input to
these jacks.
FRONT MAIN IN
When a separate pre-amplifier is
connected and this unit is used as a
power amplifier, connect the pre-
amplifier output to these jacks.
connected and this unit is used as a
power amplifier, connect the pre-
amplifier output to these jacks.
NOTE:
When you do not use the
PRE OUT and MAIN IN separately,
always connect the PRE OUT and
MAIN IN jacks with a jumper plug.
always connect the PRE OUT and
MAIN IN jacks with a jumper plug.
CENTER PRE OUT
When a separate power amplifier is
used to drive the center speaker,
connect the power amplifier input to
these jacks.
used to drive the center speaker,
connect the power amplifier input to
these jacks.
REAR PRE OUT
When a separate power amplifier is
used to drive the rear speaker, con-
nect the power amplifier input to
these jacks.
used to drive the rear speaker, con-
nect the power amplifier input to
these jacks.
19. SPEAKER TERMINALS
(1, 2 and CENTER)
(1, 2 and CENTER)
Connect the main left (L) and right (R)
speakers to the corresponding 1 and 2
speaker terminals. Connect the center
speakers to the corresponding 1 and 2
speaker terminals. Connect the center
speaker to the center (+), (-) terminals.
Make sure that the positive (+) and
negative (-) terminals on the speaker
are connected to the corresponding
terminals on the receiver.
Make sure that the positive (+) and
negative (-) terminals on the speaker
are connected to the corresponding
terminals on the receiver.
20. REAR SPEAKER
TERMINALS
TERMINALS
Connect rear speakers to the
corresponding terminals.
corresponding terminals.
21. AC INPUT CORD
Plug this cord in AC outlet on a wall.
22. SUBWOOFER OUT
When a powered subwoofer or
separate power amplifier is used to
power a subwoofer connect these
jacks to the input of the amplifier (for
subwoofer or powered subwoofer).
separate power amplifier is used to
power a subwoofer connect these
jacks to the input of the amplifier (for
subwoofer or powered subwoofer).
23. AC SWITCHED OUTLET
This outlet provides AC power. The
AC power is switched by the power
button. Use this outlet for a source
component, such as a CD player.
AC power is switched by the power
button. Use this outlet for a source
component, such as a CD player.
JSR675 OM (230V) 7/28/98 10:08 AM Page 11
10
REMOTE CONTROL
REMOTE
REMOTE ROOM
MAIN ROOM
REMOTE
COMMANDER
COMMANDER
2 SPKR
LEFT
LEFT
1 SPKR
LEFT
LEFT
1 SPKR
RIGHT
RIGHT
2 SPKR
RIGHT
RIGHT
REMOTE IR SENSOR
RECEIVER
IN
LEFT
RIGHT
OUT
MAIN IN
PRE OUT PRE OUT
PRE OUT
LEFT
RIGHT
CENTER
FRONT
REAR
SUBWOOFER
OUT
Volume
Loudness
1
2
3
4
5
P. Scan
0-30
Memory
6
7
8
9
0
FM Mode
Auto/Man
AM
FM
Tuning
Power
Speakers
1
2
VCR2
VCR2
Direct
Headphones
Set
Bass
Treble
Balance
DOLBY SURROUND
P R O • L O G I C
Surround
Input
Theater
Stadium
Center
Test
Delay
Off
3 Ch
Pro Logic
Rec
Tape 2 Mon
VCR1
Tape 1
VDP
VCR2
TV/Aux
Tuner
Phono
CD
JSR675 DOLBY® SURROUND RECEIVER
MHz
Tuned
FMST
Tuned
FMST
FM
AM
VCR 1 REC
KHz
STADIUM
THEATER
SOURCE
VDP
VCR 2
DIRECT
DOLBY 3-CH
DOLBY SURROUND
AUTO
TAPE 2 MON
PRESET
CENTER
MODE
NORM
WIDE
PHANTOM
P R O • L O G I C
MEMORY
MS
MIN
D E L AY
T I M E
S L E E P
T I M E
S L E E P
REMOTE IR SENSOR
CD
Tape1
Tape2
TV/Aux
VDP
VCR1
VCR2
CassDeck
Skip
Intro
Search
Phono
Tuner
A-B
A/B
Select
Delay
Off
Theater
Stadium
Surround
3-Stereo
Pro-Logic
Display
Sleep
Mute
RearLevel
MasterVolume
CenterLevel
CentMode
Test
Power
Tuning
PScan
Tuner
CD
1
2
3
4
5
6
7
8
9
0
%
%
&
&
#
$
-
*
*
+
+
Disc
Optional Multi-Room Control
Adapter Connection
Adapter Connection
JSR675 OM (230V) 7/28/98 10:08 AM Page 12
11
(Remove PRE OUT/MAIN IN jumpers when the front speakers are connected to external amplifier.)
R
L
LINE-IN
L
R
FRONT(left)
FRONT(right)
Power
Power Amplifier
MAIN IN
PRE OUT PRE OUT
PRE OUT
LEFT
RIGHT
CENTER
FRONT
REAR
USE 8 OHM MIN SPEAKERS
FRONT SPEAKERS
REAR SPEAKERS 8
Ω
CENTER SPEAKER
-1
-2
RIGHT
LEFT
When you drive the front speakers with another amplifier:
JSR675 OM (230V) 7/28/98 10:08 AM Page 13
Click on the first or last page to see other JSR 675 service manuals if exist.