JBL DSC 1000 (serv.man16) Service Manual ▷ View online
3
ESD PRECAUTIONS
Electrostatically Sensitive Devices (ESD)
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components com-
monly are called Electrostatically Sensitive Devices (ESD). Examples of typical ESD devices are integrated cir-
cuits and some field-effect transistors and semiconductor chip components. The following techniques should
be used to help reduce the incidence of component damage caused by static electricity.
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off
monly are called Electrostatically Sensitive Devices (ESD). Examples of typical ESD devices are integrated cir-
cuits and some field-effect transistors and semiconductor chip components. The following techniques should
be used to help reduce the incidence of component damage caused by static electricity.
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off
any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a
commercially available discharging wrist strap device, which should be removed for potential shock reasons
prior to applying power to the unit under test.
commercially available discharging wrist strap device, which should be removed for potential shock reasons
prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ESD devices, place the assembly on a conductive sur-
face such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ESD devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static"
4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static"
can generate electrical charges sufficient to damage ESD devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ESD
devices.
6. Do not remove a replacement ESD device from its protective package until immediately before you are
ready to install it. (Most replacement ESD devices are packaged with leads electrically shorted together by
conductive foam, aluminum foil or comparable conductive materials).
conductive foam, aluminum foil or comparable conductive materials).
7. Immediately before removing the protective material from the leads of a replacement ESD device, touch the
protective material to the chassis or circuit assembly into which the device will by installed.
CAUTION : BE SURE NO POWER IS APPLIED TO THE CHASSIS OR CIRCUIT, AND OBSERVE ALL
OTHER SAFETY PRECAUTIONS.
8. Minimize bodily motions when handing unpackaged replacement ESD devices. (Otherwise harmless motion
such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can gen-
erate static electricity sufficient to damage an ESD device).
erate static electricity sufficient to damage an ESD device).
DSC1000 Component list
Item
Parts No.
Qty
SPECIFICATION
Remarks(English)
1
380-B0DSC100-8000
1
Chassis
2
380-ADSC1000-8500
1
Top cover
3
380-CDSC1000-0500
1
Back panel
4
332-3DSCPT04-0000
1
Loader support
5
332-3DSCPT05-0000
1
Power button support
6
332-3DSCPT06-0000
2
Len support
7
332-3DSCPT07-0000
1
Heat-sink support
8
385-01459545-5200
1
Heat-sink
9
385-00161235-5200
2
Heat-sink, for SMPS D17 D18
10 385-00501935-5200
1
Heat-sink, for SMPS Q16
11 385-VD31ZPA2-5000
1
Aluminium alloy front panel
12 332-7DSCPT11-0000
2
Net cover on front panel
13 330-ADSCPT12-0000
1
Baffle for tray door
14 600-000H0205-0020
1
Amplifier speaker output label
15 385-00282810-0000
1
Heat-sink, for MainBoard U4
16 332-10MV7200-0000
2
Decorate lamp holder
MV7200
17 500-09130126-0000
1
Insulated underlay for AC cord
130×126mm
18 500-10202011-0010
1
Insulated underlay for SMPS
20×20×11mm
19 331-1000RE01-8000
1
Button
20 331-1000RE02-8000
1
Power button
21 330-2000RE03-8000
1
Disc tray door
22 331-8000RE04-8000
1
Len for tray door
23 331-8000RE05-8000
1
Len for VFD VFD
24 330-ADSCRE06-0000
1
Left baffle
25 330-ADSCRE07-0000
1
Right baffle
26 331-5VD28016-7000
1
Power indicator lampshade
27 331-3000RE12-0000
1
Volume knob
28 331-4DSC1000-4000
4
Pedestal
bronzing, size same as DVD 25, specify color
29 350-0DSC1000-0000
4
Pedestal underlay
same as DVD25
30 332-200SZ003-0200
1
IR receiver head frame
SZ003
28×28×10mm
DSC1000-RE01
DSC1000-RE02
DSC1000-RE03
DSC1000-RE04
DSC1000-RE05
DSC1000-RE02
DSC1000-RE03
DSC1000-RE04
DSC1000-RE05
DSC1000-RE12
DSC1000-PT03
DSC1000-PT04
DSC1000-PT04
DSC1000-RE08
DSC1000-PT12
DSC1000-H02
DSC1000-H02
DSC1000-RE07
DSC1000-PT11
DSC1000-PT09
DSC1000-RE06
METAL PART
PLASTIC PART
DSC1000-PT05
DSC1000-PT06
DSC1000-PT07
DSC1000-PT08, 145×95×45mm
DSC1000-PT06
DSC1000-PT07
DSC1000-PT08, 145×95×45mm
DSC1000-PT01
16X12X35mm
50X19X35mm
50X19X35mm
DSC1000-PT02
Harman Consumer Group
Components
JBL DSC1000/230
Click on the first or last page to see other DSC 1000 (serv.man16) service manuals if exist.