DOWNLOAD JBL ATX 30 (serv.man10) Service Manual ↓ Size: 976.47 KB | Pages: 10 in PDF or view online for FREE

Model
ATX 30 (serv.man10)
Pages
10
Size
976.47 KB
Type
PDF
Document
User Manual / Operation Manual
Brand
Device
Audio
File
atx-30-sm10.pdf
Date

JBL ATX 30 (serv.man10) User Manual / Operation Manual ▷ View online

9
Subwoofer
Crossover
Subwoofer
Level
Volume
Subwoofer playback level can
be adjusted using the rear panel
Volume control. For detailed
information on fine-tuning
Volume and Crossover
Frequency, see page 6.
Crossover Frequency
The crossover frequency knob
determines the highest
frequency your subwoofer will
reproduce. It allows a seamless
transition from the subwoofer
to the satellite speakers.
Experiment with this adjustment
to find the crossover frequency
that sounds best in your room.
For subwoofers used with
Surround Sound processors
with dedicated subwoofer out-
puts, the best result will be
obtained with the control at the
150 Hz“ position. 
If there is no sound from any of the
speakers:
• Check that receiver/amplifier is on
and a source is playing.
• Check that the powered subwoofer is
plugged in, its Power switch is
switched to the “ON” position.
• Check all wires and connections
between receiver/amplifier and
speakers. Make sure all wires are
connected. Make sure none of the
speaker wires are frayed, cut or
punctured.
• Review proper operation of your
receiver/amplifier.
If there is no sound coming from one
speaker:
• Check the “Balance” control on your
receiver/amplifier.
• Check all wires and connections
between receiver/amplifier and
speakers. Make sure all wires are
connected. Make sure none of the
speaker wires are frayed, cut or
punctured.
• In Dolby Digital or DTS
®
modes, make
sure that the receiver/processor is
configured so that the speaker in
question is enabled.
If there is no sound from the center
speaker:
• Check all wires and connections
between receiver/amplifier and
speaker. Make sure all wires are con-
nected. Make sure none of the
speaker wires are frayed, cut or
punctured.
• If your receiver/processor is set in
Dolby Pro Logic mode, make sure the 
center speaker is not in phantom
mode.
• If your receiver/processor is set in
Dolby Digital or DTS
®
mode, make
sure the receiver/processor is con-
figured so that the center speaker is
enabled.
If the system plays at low volumes but
shuts off as volume is increased:
• Check all wires and connections
between receiver/amplifier and
speakers. Make sure all wires are
connected. Make sure none of the
speaker wires are frayed, cut or
punctured.
• If more than one pair of main speak-
ers is being used, check the minimum
impedance requirements of your
receiver/amplifier.
If there is low (or no) bass output:
• Make sure the connections to the left
and right “Speaker Inputs” have the
correct polarity (+ and –).
• Make sure the subwoofer is plugged
into an active electrical outlet.
• Make sure the powered subwoofer is
plugged in and switched on.
• In Dolby Digital or DTS
®
modes, make
sure your receiver/processor is con-
figured so that the subwoofer and LFE
output are enabled.
If there is no sound from the surround
speakers:
• Check all wires and connections
between receiver/amplifier and
speakers. Make sure all wires are
connected. Make sure none of the
speaker wires are frayed, cut or
punctured.
• Review proper operation of your
receiver/amplifier and its surround-
sound features.
• Make sure the movie or TV show you
are watching is recorded in a sur-
round-sound mode. If it is not, check
to see if your receiver/amplifier has
other surround modes you may use.
• In Dolby Digital or DTS
®
modes, make
sure your receiver/processor is con-
figured so that the surround speakers
are enabled.
• Review the operation of your DVD
player and the jacket of your DVD to
make sure that the DVD features the
desired Dolby Digital or DTS
®
mode,
and that you have properly selected
that mode using both the DVD play-
er’s menu and the DVD disc’s menu.
TROUBLESHOOTING
JBL Consumer Products
250 Crossways Park Drive, Woodbury, NY 11797
©2002 JBL, Incorporated. 
JBL is a registered trademark of JBL, Incorporated.
Part No.1111-ATXSERIES
Refinements may be made on occasion to existing products without notice, but will always meet or exceed original specifications unless
otherwise stated.
*Dolby and Pro Logic are trademarks of Dolby Laboratories. DTS
®
is a registered trademark of Digital Theater Systems, Inc.
ATX
20
30
40
Type:
2-way
3-way
3-way
Frequency Response:
75Hz–20kHz
55Hz–20kHz
55Hz–20kHz
Sensitivity (2.83V/1m):
86dB
88dB
89dB
Nominal Impedance:
6 Ohms
6 Ohms
6 Ohms
Power Handling Peak/Continuous:
100/60 Watts RMS
150/100 Watts RMS
200/160 Watts RMS
Recommended Amplifier Power*:
20 – 60 Watts
20 - 80 Watts
30 - 120 Watts
RMS per Channel
RMS per Channel
RMS per Channel
Crossover Frequency:
4000Hz
800/3500Hz
800/3500Hz
Connection:
Single wired with 5-way
Single wired with 5-way
Single wired with 5-way
binding posts
binding posts
binding posts
High Frequency Driver:
10mm Titanium Laminate 
10mm Titanium Laminate
10mm Titanium Laminate
Dome tweeter
Dome tweeter
Dome tweeter
Midrange Frequency Driver:
-
100mm Laminated 
100mm Laminated 
-
Paper Cone
Paper Cone
Low Frequency Driver:
165mm Laminated 
165mm Laminated
Two 165mm Laminated
Paper Cone
Paper Cone
Paper Cones
Finish:
Black Ash or Beech Vinyl Laminate with Dark Grey Grille
Dimensions (H x W x D):
350 x 202 x 237mm
865 x 202 x 286mm
865 x 202 x 286mm
Weight (per piece):
5kg
13.5kg
14.5kg
ATX
60
10C Center
100S Subwoofer
Type:
3-way
2-way
Active Subwoofer
Frequency Response:
50Hz–20kHz
80Hz–20kHz
45Hz–150Hz
Sensitivity (2.83V/1m):
89dB
86dB
-
Nominal Impedance:
6 Ohms
6 Ohms
-
Power Handling Peak/Continuous:
200/160 Watts RMS
100/60 Watts RMS
-
Recommended Amplifier Power*:
40 – 120 Watts
20 – 60 Watts
100 Watts
RMS per Channel
RMS per Channel
RMS (1% THD)
Crossover Frequency:
800/3500Hz
3500Hz
-
Connection:
Single wired with 5-way 
Single wired with 5-way
5-way binding posts
binding posts
binding posts
Stereo in (RCA Phono)
LFE in (RCA Phono)
High Frequency Driver:
10mm Titanium Laminate 
10mm Titanium Laminate
-
Dome tweeter
Dome tweeter
Midrange Frequency Driver:
100mm Laminated 
-
-
Paper Cone
-
Low Frequency Driver:
250mm Laminated 
Two 100mm Laminated Paper
200mm Laminated
Paper Cone
Cones, Magnetically Shielded Paper Cone
Finish:
Black Ash or Beech Vinyl Laminate with Dark Grey Grille
Dimensions (H x W x D):
950 x 286 x 315mm
158 x 410 x131mm
350 x 295 x 350mm
Weight (per piece):
20kg
3kg
13kg
*Recommended Amplifier range is provided as a guideline only. Use of underpowered amplifiers may result in damage to the loudspeakers.
ATX20/30/40/60/10C/100S (230V)
ATX Series
O W N E R ’ S   G U I D E
PRODUCT LINE: 
DESIGN GOAL: Bring the thrill of live performance and movie sound to the
home environment by calling on JBL’s professional engineering leadership.
PROFESSIONAL REFERENCE: Home Loudspeaker Series
MODEL
NUMBER:
P R O   S O U N D  
C O M E S   H O M E
SPECIFICATIONS 
JBL Consumer Products
250 Crossways Park Drive, Woodbury, NY 11797
©2002 JBL, Incorporated. 
JBL is a registered trademark of JBL, Incorporated.
Part No.1111-ATXSERIES
Refinements may be made on occasion to existing products without notice, but will always meet or exceed original specifications unless
otherwise stated.
*Dolby and Pro Logic are trademarks of Dolby Laboratories. DTS
®
is a registered trademark of Digital Theater Systems, Inc.
ATX
20
30
40
Type:
2-way
3-way
3-way
Frequency Response:
75Hz–20kHz
55Hz–20kHz
55Hz–20kHz
Sensitivity (2.83V/1m):
86dB
88dB
89dB
Nominal Impedance:
6 Ohms
6 Ohms
6 Ohms
Power Handling Peak/Continuous:
100/60 Watts RMS
150/100 Watts RMS
200/160 Watts RMS
Recommended Amplifier Power*:
20 – 60 Watts
20 - 80 Watts
30 - 120 Watts
RMS per Channel
RMS per Channel
RMS per Channel
Crossover Frequency:
4000Hz
800/3500Hz
800/3500Hz
Connection:
Single wired with 5-way
Single wired with 5-way
Single wired with 5-way
binding posts
binding posts
binding posts
High Frequency Driver:
10mm Titanium Laminate 
10mm Titanium Laminate
10mm Titanium Laminate
Dome tweeter
Dome tweeter
Dome tweeter
Midrange Frequency Driver:
-
100mm Laminated 
100mm Laminated 
-
Paper Cone
Paper Cone
Low Frequency Driver:
165mm Laminated 
165mm Laminated
Two 165mm Laminated
Paper Cone
Paper Cone
Paper Cones
Finish:
Black Ash or Beech Vinyl Laminate with Dark Grey Grille
Dimensions (H x W x D):
350 x 202 x 237mm
865 x 202 x 286mm
865 x 202 x 286mm
Weight (per piece):
5kg
13.5kg
14.5kg
ATX
60
10C Center
100S Subwoofer
Type:
3-way
2-way
Active Subwoofer
Frequency Response:
50Hz–20kHz
80Hz–20kHz
45Hz–150Hz
Sensitivity (2.83V/1m):
89dB
86dB
-
Nominal Impedance:
6 Ohms
6 Ohms
-
Power Handling Peak/Continuous:
200/160 Watts RMS
100/60 Watts RMS
-
Recommended Amplifier Power*:
40 – 120 Watts
20 – 60 Watts
100 Watts
RMS per Channel
RMS per Channel
RMS (1% THD)
Crossover Frequency:
800/3500Hz
3500Hz
-
Connection:
Single wired with 5-way 
Single wired with 5-way
5-way binding posts
binding posts
binding posts
Stereo in (RCA Phono)
LFE in (RCA Phono)
High Frequency Driver:
10mm Titanium Laminate 
10mm Titanium Laminate
-
Dome tweeter
Dome tweeter
Midrange Frequency Driver:
100mm Laminated 
-
-
Paper Cone
-
Low Frequency Driver:
250mm Laminated 
Two 100mm Laminated Paper
200mm Laminated
Paper Cone
Cones, Magnetically Shielded Paper Cone
Finish:
Black Ash or Beech Vinyl Laminate with Dark Grey Grille
Dimensions (H x W x D):
950 x 286 x 315mm
158 x 410 x131mm
350 x 295 x 350mm
Weight (per piece):
20kg
3kg
13kg
*Recommended Amplifier range is provided as a guideline only. Use of underpowered amplifiers may result in damage to the loudspeakers.
ATX20/30/40/60/10C/100S (230V)
ATX Series
O W N E R ’ S   G U I D E
PRODUCT LINE: 
DESIGN GOAL: Bring the thrill of live performance and movie sound to the
home environment by calling on JBL’s professional engineering leadership.
PROFESSIONAL REFERENCE: Home Loudspeaker Series
MODEL
NUMBER:
P R O   S O U N D  
C O M E S   H O M E
SPECIFICATIONS 
JBL Consumer Products
250 Crossways Park Drive, Woodbury, NY 11797
©2002 JBL, Incorporated. 
JBL is a registered trademark of JBL, Incorporated.
Part No.1111-ATXSERIES
Refinements may be made on occasion to existing products without notice, but will always meet or exceed original specifications unless
otherwise stated.
*Dolby and Pro Logic are trademarks of Dolby Laboratories. DTS
®
is a registered trademark of Digital Theater Systems, Inc.
ATX
20
30
40
Type:
2-way
3-way
3-way
Frequency Response:
75Hz–20kHz
55Hz–20kHz
55Hz–20kHz
Sensitivity (2.83V/1m):
86dB
88dB
89dB
Nominal Impedance:
6 Ohms
6 Ohms
6 Ohms
Power Handling Peak/Continuous:
100/60 Watts RMS
150/100 Watts RMS
200/160 Watts RMS
Recommended Amplifier Power*:
20 – 60 Watts
20 - 80 Watts
30 - 120 Watts
RMS per Channel
RMS per Channel
RMS per Channel
Crossover Frequency:
4000Hz
800/3500Hz
800/3500Hz
Connection:
Single wired with 5-way
Single wired with 5-way
Single wired with 5-way
binding posts
binding posts
binding posts
High Frequency Driver:
10mm Titanium Laminate 
10mm Titanium Laminate
10mm Titanium Laminate
Dome tweeter
Dome tweeter
Dome tweeter
Midrange Frequency Driver:
-
100mm Laminated 
100mm Laminated 
-
Paper Cone
Paper Cone
Low Frequency Driver:
165mm Laminated 
165mm Laminated
Two 165mm Laminated
Paper Cone
Paper Cone
Paper Cones
Finish:
Black Ash or Beech Vinyl Laminate with Dark Grey Grille
Dimensions (H x W x D):
350 x 202 x 237mm
865 x 202 x 286mm
865 x 202 x 286mm
Weight (per piece):
5kg
13.5kg
14.5kg
ATX
60
10C Center
100S Subwoofer
Type:
3-way
2-way
Active Subwoofer
Frequency Response:
50Hz–20kHz
80Hz–20kHz
45Hz–150Hz
Sensitivity (2.83V/1m):
89dB
86dB
-
Nominal Impedance:
6 Ohms
6 Ohms
-
Power Handling Peak/Continuous:
200/160 Watts RMS
100/60 Watts RMS
-
Recommended Amplifier Power*:
40 – 120 Watts
20 – 60 Watts
100 Watts
RMS per Channel
RMS per Channel
RMS (1% THD)
Crossover Frequency:
800/3500Hz
3500Hz
-
Connection:
Single wired with 5-way 
Single wired with 5-way
5-way binding posts
binding posts
binding posts
Stereo in (RCA Phono)
LFE in (RCA Phono)
High Frequency Driver:
10mm Titanium Laminate 
10mm Titanium Laminate
-
Dome tweeter
Dome tweeter
Midrange Frequency Driver:
100mm Laminated 
-
-
Paper Cone
-
Low Frequency Driver:
250mm Laminated 
Two 100mm Laminated Paper
200mm Laminated
Paper Cone
Cones, Magnetically Shielded Paper Cone
Finish:
Black Ash or Beech Vinyl Laminate with Dark Grey Grille
Dimensions (H x W x D):
950 x 286 x 315mm
158 x 410 x131mm
350 x 295 x 350mm
Weight (per piece):
20kg
3kg
13kg
*Recommended Amplifier range is provided as a guideline only. Use of underpowered amplifiers may result in damage to the loudspeakers.
ATX20/30/40/60/10C/100S (230V)
ATX Series
O W N E R ’ S   G U I D E
PRODUCT LINE: 
DESIGN GOAL: Bring the thrill of live performance and movie sound to the
home environment by calling on JBL’s professional engineering leadership.
PROFESSIONAL REFERENCE: Home Loudspeaker Series
MODEL
NUMBER:
P R O   S O U N D  
C O M E S   H O M E
SPECIFICATIONS 
Page of 10
Display

JBL ATX 30 (serv.man10) User Manual / Operation Manual ▷ Download