Harman Kardon HTFS 2 (serv.man7) User Manual / Operation Manual ▷ View online
HTFS
2
Floor Stands
OWNER’S MANUAL
Power for the Digital Revolution
®
2 INTRODUCTION
Introduction
Introduction
Thank you for purchasing Harman Kardon HTFS
2 floor stands. These stands are designed to
enhance your enjoyment of a Harman Kardon
HKTS 7 or HKTS 11 home cinema loudspeaker
system by expanding your speaker-placement
options to create the optimum audio presen-
tation. The HTFS 2 stands are also compatible
with Harman Kardon HKS 3 and HKS 4
loudspeakers.
2 floor stands. These stands are designed to
enhance your enjoyment of a Harman Kardon
HKTS 7 or HKTS 11 home cinema loudspeaker
system by expanding your speaker-placement
options to create the optimum audio presen-
tation. The HTFS 2 stands are also compatible
with Harman Kardon HKS 3 and HKS 4
loudspeakers.
To obtain maximum enjoyment of your home
theater system, we ask you to spend a few
minutes reading the speaker placement and
setup instructions in the owner’s manual
supplied with your loudspeakers, and a few
moments reviewing the assembly instructions for
your HTFS 2 floor stands. If you have any
questions about this product or its installation,
or about your loudspeakers, please contact your
Harman Kardon dealer, who is your best local
source of information.
theater system, we ask you to spend a few
minutes reading the speaker placement and
setup instructions in the owner’s manual
supplied with your loudspeakers, and a few
moments reviewing the assembly instructions for
your HTFS 2 floor stands. If you have any
questions about this product or its installation,
or about your loudspeakers, please contact your
Harman Kardon dealer, who is your best local
source of information.
Included
Two floor stand columns
Two mounting plates
Eight rubber pads
Eight floor spikes
Eight round Phillips-head screws for
assembling the stands
(M5-0.8P, 19mm or #10-32, 3/4" long)
assembling the stands
(M5-0.8P, 19mm or #10-32, 3/4" long)
Two weighted bases
ASSEMBLY 3
Assembly
Assembly
1. If you will be placing the HTFS 2 stands on a
hard surface, such as a wood or tile floor,
attach four of the supplied self-adhesive
rubber pads to the underside of the base in
the recesses as indicated in the drawing.
attach four of the supplied self-adhesive
rubber pads to the underside of the base in
the recesses as indicated in the drawing.
Place rubber pads or floor spikes here
2. If you will be using the HTFS 2 stands on a
carpeted surface, screw four of the supplied
floor spikes into the base using the threaded
inserts in the recesses as shown in the
drawing.
floor spikes into the base using the threaded
inserts in the recesses as shown in the
drawing.
3. Following the instructions on pages 9 through
12 of the owner’s manual provided with your
HKTS system, thread the appropriate speaker
cable through the hole in the center of the
base, being careful to avoid the two screw
holes. Then feed the cable through the length
of the column from the bottom until it comes
out the top.
HKTS system, thread the appropriate speaker
cable through the hole in the center of the
base, being careful to avoid the two screw
holes. Then feed the cable through the length
of the column from the bottom until it comes
out the top.
4. Attach the column to the base using two of
the supplied screws.
The column should be placed so that the
lower rim of the column is on that side of the
base plate where the Harman Kardon logo is.
The column should be placed so that the
lower rim of the column is on that side of the
base plate where the Harman Kardon logo is.
5. Thread the speaker cable through the hole in
the center of the mounting plate, being
careful to avoid the three screw holes.
careful to avoid the three screw holes.
6. Attach the mounting plate to the top of the
column using two of the supplied screws.
The mounting plate tab with the third screw
hole should sit on the higher rim of the
column.
The mounting plate tab with the third screw
hole should sit on the higher rim of the
column.
Attaching the Speaker to the
Stand
Stand
1. Unscrew the bolt that attaches the black shelf
stand to the bottom of the speaker. Store the
stand in a safe place in case it is needed for
a future installation. The bolt will be used
to attach the speaker to the floor stand
mounting plate.
stand in a safe place in case it is needed for
a future installation. The bolt will be used
to attach the speaker to the floor stand
mounting plate.
2. Insert the speaker wires into the terminals on
the bottom of the speaker, being careful to
observe the correct polarity.
observe the correct polarity.
3. Place the speaker on top of the mounting
plate with the remaining screw hole lined up
with the threaded insert on the bottom of the
speaker.
with the threaded insert on the bottom of the
speaker.
4. Insert the bolt that was used for the shelf
stand up through the remaining screw hole
and into the speaker.
and into the speaker.
Repeat the assembly and speaker attachment
processes for each floor stand in your system,
and adjust the final speaker placement as
indicated in the owner’s manual supplied with
the speakers. You are now ready to enjoy your
home theater system!
processes for each floor stand in your system,
and adjust the final speaker placement as
indicated in the owner’s manual supplied with
the speakers. You are now ready to enjoy your
home theater system!
Remove
Stand
Stand
15mm
or 1/2"
Lower rim
Higher rim
Specifications
250 Crossways Park Drive, Woodbury, New York 11797
www.harmankardon.com
Harman Consumer International:
2, Route de Tours, 72500 Château-du-Loir, France
© 2004 Harman Kardon, Incorporated
Part 406-000-05009
www.harmankardon.com
Harman Consumer International:
2, Route de Tours, 72500 Château-du-Loir, France
© 2004 Harman Kardon, Incorporated
Part 406-000-05009
Dimensions (Product):
Height: 875mm (34-1/2") assembled, not including floor spikes and without speaker
Base: 227mm x 178mm oval (9"x 7")
Base: 227mm x 178mm oval (9"x 7")
Shipping Dimensions (H x W x D):
88mm x 888mm x 240mm
(3-1/2"x 35"x 9-1/2")
(3-1/2"x 35"x 9-1/2")
Weight (Product):
7.5kg (16.7 lb)
Shipping Weight:
8.6kg (19.1 lb)
All features and specifications are subject to change without notice.
Harman Kardon and Power for the Digital Revolution are registered trademarks of Harman International Industries, Incorporated.
Display
