HKTS 2 SUB SYSTEM (serv.man2) — Harman Kardon Audio User Guide / Operation Manual

Model
HKTS 2 SUB SYSTEM (serv.man2)
Pages
12
Size
133.96 KB
Type
PDF
Document
User Guide / Operation Manual
Brand
Device
Audio
File
hkts-2-sub-system-sm2.pdf
Date

View Harman Kardon HKTS 2 SUB SYSTEM (serv.man2) User Guide / Operation Manual online

250 Crossways Park Drive, Woodbury, New York 11797 
1-800/422-8027 (USA only)  Fax: 516/682-3523
© 2000 Harman Kardon, Incorporated 
Printed 9/00   
Part No. ai5083
HKTS 2 System
Frequency Response
35Hz – 20kHz (–6dB)
Satellites
Recommended Power 
10 – 50 watts 
Impedance
8 ohms nominal 
Sensitivity
86dB @ 1 watt/1 meter
Tweeter
One 1/2" dome, video-shielded
Midrange
One 3" driver, video-shielded
Dimensions (H x W x D) 
4-5/8" x 3-1/8" x 3-3/4"
117mm x 79mm x 93mm
Weight
1.1 lb/0.5kg 
Center
Recommended Power 
10 – 50 watts 
Impedance
8 ohms nominal 
Sensitivity
86dB @ 1 watt/1 meter
Tweeter
One 1/2" dome, video-shielded
Midrange
Dual 3" drivers, video-shielded
Dimensions (H x W x D)
3-1/2" x 7-5/8" x 3-3/4"
89mm x 194mm x 93mm
Weight
1.89 lb/0.86kg 
Subwoofer
Amplifier 
100 watts RMS
Bass
10" woofer, bass-reflex enclosure
Dimensions (H x W x D) 
18-1/4" x 15-3/4" x 16-3/4"
464mm x 400mm x 425mm
Weight 
35.8 lb/16.2kg 
Refinements may be made on occasion to existing products without notice,
but will always meet or exceed original specifications unless otherwise stated.
* Trademarks of Dolby Laboratories.
DTS is a registered trademark of Digital Theater Systems, Inc.
SPECIFICATIONS
HKTS 2 Home-Theater Speaker System
OWNER’S MANUAL
Power for the digital revolution.
®
2
Table of Contents
3
Safety Information
4
Introduction
4
Included
5
Speaker Placement
6
Mounting Options
7
Speaker Connections
7
Speaker-Level Connection Guide
8
Dolby* Pro Logic* (Non-Digital) – Speaker Level
9
Dolby Pro Logic (Non-Digital) – Line Level
9
Dolby Digital or DTS
®
(or other Digital Surround Mode) Connection
10
Operation
10
Volume
11
Troubleshooting
12
Specifications
3
Read First! Important Safety Precautions!
1. Read Instructions. All the safety and operating
instructions should be read before the product is
operated.
2. Retain Instructions. The safety and operating
instructions should be retained for future reference.
3. Heed Warnings. All warnings on the product and
in the operating instructions should be adhered to.
4. Follow Instructions. All operating and use
instructions should be followed.
5. Cleaning. Unplug this product from the wall out-
let before cleaning. Do not use liquid cleaners or
aerosol cleaners. Use a damp cloth for cleaning.
6. Attachments. Do not use attachments not rec-
ommended by the product manufacturer, as they
may cause hazards.
7. Water and Moisture. Do not use this product
near water – for example, near a bathtub, wash bowl,
kitchen sink or laundry tub; in a wet basement;
near a swimming pool; or the like.
8. Accessories. Do not place this product on an
unstable cart, stand, tripod, bracket or table. The
product may fall, causing serious injury to a child 
or adult, and serious damage to the product. Use
only with a cart, stand, tripod, bracket or table 
recommended by the manufacturer, or sold with the
product. Any mounting of the product should follow
the manufacturer’s instructions, and should use 
a mounting accessory recommended by the manu-
facturer.
9. A Product and Cart Combination
Should Be Moved with Care. 
Quick
stops, excessive force and uneven sur-
faces may cause the product and cart
combination to overturn.
10. Ventilation. Slots and openings in the cabinet
are provided for ventilation and to ensure reliable
operation of the product and to protect it from
overheating, and these openings must not be
blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug
or other similar surface. This product should not be
placed in a built-in installation, such as 
a bookcase or rack, unless proper ventilation is pro-
vided or the manufacturer’s instructions have been
adhered to.
11. Power Sources. This product should be operated
only from the type of power source indicated on the
marking label. If you are not sure of the type of
power supply to your home, consult your product
dealer or local power company. For products intend-
ed to operate from battery power, or other sources,
refer to the operating instructions.
12. Polarization. This product may be
equipped with a polarized alternating-current-line
plug (a plug having one blade wider than the
other). This plug will fit into the power outlet only
one way. This is a safety feature. If you are unable
to insert the plug fully into the outlet, try reversing
the plug. If the plug should still fail to fit, contact
your electrician to replace your 
obsolete outlet. Do not defeat the safety 
purpose of the polarized plug.
13. Power-Cord Protection. Power-supply cords
should be routed so that they are not likely to be
walked on or pinched by items placed upon or
against them, paying particular attention to cords
at plugs, convenience receptacles, and the point
where they exit from the product.
14. Nonuse Periods. The power cord of the product
should be unplugged from the outlet when left
unused for long periods of time.
15. Outdoor Antenna Grounding. If an outside
antenna or cable system is connected to the prod-
uct, be sure the antenna or cable system is ground-
ed so as to provide some protection against voltage
surges and built-up static charges. Article 810 of
the National Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of the
mast and supporting structure, grounding of the
lead-in wire to an antenna discharge unit, size of
grounding conductors, location of antenna-dis-
charge unit, connection to grounding electrodes,
and requirements for the grounding electrode. See
Figure 1.
16. Lightning. For added protection for this prod-
uct during a lightning storm, or when it is left
unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the
antenna or cable system. This will prevent damage
to the product due to lightning and power-line
surges.
17. Power Lines. An outside antenna system should
not be located in the vicinity of overhead power
lines or other electric light or power circuits, or
where it can fall into such power lines or circuits.
When installing an outside antenna system, extreme
care should be taken to keep from touching such
power lines or circuits, as contact with them might
be fatal.
18. Overloading. Do not overload wall outlets,
extension cords, or integral convenience recepta-
cles, as this can result in a risk of fire or electric
shock.
19. Object and Liquid Entry. Never push objects of
any kind into this product through openings, as
they may touch dangerous voltage points or short-
out parts that could result in a fire or electric
shock. Never spill liquid of any kind on the product.
20. Servicing. Do not attempt to service this prod-
uct yourself, as opening or removing covers may
expose you to dangerous voltage or other hazards.
Refer all servicing to qualified service personnel.
21. Damage Requiring Service. Unplug this prod-
uct from the wall outlet and refer servicing to quali-
fied service personnel under the following condi-
tions:
a. The power-supply cord or the plug has been
damaged; or
b. Objects have fallen onto, or liquid has been
spilled into, the product; or
c. The product has been exposed to rain or water;
or
d. The product does not operate normally when fol-
lowing the operating instructions. Adjust only those
controls that are covered by the operating instruc-
tions, as an improper adjustment of other controls
may result in damage and will often require exten-
sive work by a qualified technician to restore the
product to its normal operation; or
e. The product has been dropped or damaged in any
way; or
f. The product exhibits a distinct change in perfor-
mance; this indicates a need for service.
22. Replacement Parts. When replacement parts
are required, be sure the service technician has used
replacement parts specified by the manufacturer or
that have the same characteristics as the original
part. Unauthorized substitutions may result in fire,
electric shock or other hazards.
23. Safety Check. Upon completion of any service
or repairs to this product, ask the service technician
to perform safety checks to determine that the
product is in proper operating condition.
24. Wall or Ceiling Mounting. The product should
be mounted to a wall or ceiling only as recommend-
ed by the manufacturer.
25. Heat. The product should be situated away from
heat sources such as radiators, heat registers,
stoves or other products (including amplifiers) that
produce heat.
Antenna Lead-In Wire
Ground Clamp
Antenna Discharge Unit (NEC Section 810-20)
Grounding Conductors (NEC Section 810-21)
Electric Service Equipment
Ground Clamps
Power Service Grounding Electrode System
(NEC Art. 250, Part H) 
Figure 1.
Example of Antenna Grounding as per 
National Electrical Code ANSI/NFPA 70
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: To prevent electric shock,
 do not use this (polarized) 
plug with an extension cord, 
receptacle or other outlet 
unless the blades can 
be fully inserted to 
prevent blade exposure.
The lightning flash with arrowhead symbol, 
within an equilateral triangle, is intended to 
alert the user to the presence of uninsulated 
“dangerous voltage” within the product’s 
enclosure that may be of sufficient magnitude to constitute a 
risk of electric shock to persons.
The exclamation point within an equilateral 
triangle is intended to alert the user to the 
presence of important operating and 
maintenance (servicing) instructions in the 
literature accompanying the appliance.
Part No. HCGULB 08/00
Page of 12
Display

Download Harman Kardon HKTS 2 SUB SYSTEM (serv.man2) User Guide / Operation Manual

Here you can view online or download Harman Kardon HKTS 2 SUB SYSTEM (serv.man2) User Guide / Operation Manual in pdf. This User Guide / Operation Manual can help you recover, restore, fix, disassemble and repair Harman Kardon HKTS 2 SUB SYSTEM (serv.man2) Audio. Information contained in Harman Kardon HKTS 2 SUB SYSTEM (serv.man2) service manual (repair manual) typically includes:

  • Disassembly, troubleshooting, programming, maintenance, remote, adjustment, installation and setup instructions.
  • Schematics, wiring and block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Parts list (bill of materials).