Harman Kardon HKTS 1 SUB SYSTEM (serv.man2) User Manual / Operation Manual ▷ View online
Mode
Procedure
LED Status
Off
Receiver/amplifier off.
Off
On
Receiver/amplifier on and playing program material.
Green
Standby
Simply turn off your receiver/amplifier. The subwoofer will
Red
turn off after approximately twenty minutes. The subwoofer
will turn on when your receiver/amplifier begins playing again.
will turn on when your receiver/amplifier begins playing again.
min max
Subwoofer
Level
min max
Subwoofer
Level
Volume
OPERATION
9
HKTS 1 OM 6/27/99 11:35 PM Page 11
If there is no sound from any of the
speakers, check the following:
speakers, check the following:
• Receiver/amplifier is on and a source is
playing.
• Powered subwoofer is plugged in and is
either in the “On” or “Auto” position.
• Check all wires and connections between
receiver/amplifier and speakers. Make
sure all wires are connected. Make sure
none of the speaker wires are frayed, cut
or punctured.
• Review proper operation of your
receiver/amplifier.
playing.
• Powered subwoofer is plugged in and is
either in the “On” or “Auto” position.
• Check all wires and connections between
receiver/amplifier and speakers. Make
sure all wires are connected. Make sure
none of the speaker wires are frayed, cut
or punctured.
• Review proper operation of your
receiver/amplifier.
If there is no sound coming from one
speaker, check the following:
speaker, check the following:
• Check the “Balance” control on your
receiver/amplifier.
• Check all wires and connections between
receiver/amplifier and speakers. Make
sure all wires are connected. Make sure
none of the speaker wires are frayed,
cut or punctured.
receiver/amplifier.
• Check all wires and connections between
receiver/amplifier and speakers. Make
sure all wires are connected. Make sure
none of the speaker wires are frayed,
cut or punctured.
If the system plays at low volumes
but shuts off as volume is increased,
check the following:
but shuts off as volume is increased,
check the following:
• Check all wires and connections between
receiver/amplifier and speakers. Make
sure all wires are connected. Make sure
none of the speaker wires are frayed,
cut or punctured.
• If more than one pair of main speakers is
being used, check the minimum impedance
requirements of your receiver/amplifier.
receiver/amplifier and speakers. Make
sure all wires are connected. Make sure
none of the speaker wires are frayed,
cut or punctured.
• If more than one pair of main speakers is
being used, check the minimum impedance
requirements of your receiver/amplifier.
If there is low bass output, check the
following:
following:
• Make sure the connections to the left and
right “Speaker Inputs” have the correct
polarity (+ and –).
• Make sure that the subwoofer is plugged
into an active electrical outlet.
• Powered subwoofer is plugged in and is
either in the “On” or “Auto” position.
right “Speaker Inputs” have the correct
polarity (+ and –).
• Make sure that the subwoofer is plugged
into an active electrical outlet.
• Powered subwoofer is plugged in and is
either in the “On” or “Auto” position.
If there is no sound from the sur-
round speakers, check the following:
round speakers, check the following:
• Check all wires and connections between
receiver/amplifier and speakers. Make
sure all wires are connected. Make sure
none of the speaker wires are frayed,
cut or punctured.
• Review proper operation of your
receiver/amplifier and its surround
sound features.
• Make sure the movie or TV show you are
watching is recorded in Dolby* surround.
If it is not, check to see if your receiver/
amplifier has other surround modes you
may use.
receiver/amplifier and speakers. Make
sure all wires are connected. Make sure
none of the speaker wires are frayed,
cut or punctured.
• Review proper operation of your
receiver/amplifier and its surround
sound features.
• Make sure the movie or TV show you are
watching is recorded in Dolby* surround.
If it is not, check to see if your receiver/
amplifier has other surround modes you
may use.
TROUBLESHOOTING
10
HKTS 1 OM 6/27/99 11:35 PM Page 12
HKTS1 System
Frequency Response
35Hz – 20kHz (–6dB)
35Hz – 20kHz (–6dB)
Sat-TS1
Recommended Power
10 – 50 watts
Nominal Impedance
8 ohms
Sensitivity
86dB @ 1 watt @1 meter
Tweeter
One 1/2"-dome, video
shielded
Midrange
3" driver, video shielded
Dimensions (H x W x D)
4-5/8 x 3-1/8 x 2-7/8 inches
118 x 80 x 73mm
Weight
1 lb/.46 kg
10 – 50 watts
Nominal Impedance
8 ohms
Sensitivity
86dB @ 1 watt @1 meter
Tweeter
One 1/2"-dome, video
shielded
Midrange
3" driver, video shielded
Dimensions (H x W x D)
4-5/8 x 3-1/8 x 2-7/8 inches
118 x 80 x 73mm
Weight
1 lb/.46 kg
Sub-TS1
Amplifier
75 watts RMS
Bass
8" woofer, bass-reflex
enclosure
Dimensions (H x W x D)
10-1/2 x 18-1/2 x 10-1/2 inches
267 x 470 x 267mm
Weight
29.9 lbs/13.6 kg
75 watts RMS
Bass
8" woofer, bass-reflex
enclosure
Dimensions (H x W x D)
10-1/2 x 18-1/2 x 10-1/2 inches
267 x 470 x 267mm
Weight
29.9 lbs/13.6 kg
Refinements may be made on occasion
to existing products without notice, but
will always meet or exceed original
specifications unless otherwise stated.
to existing products without notice, but
will always meet or exceed original
specifications unless otherwise stated.
SPECIFICATIONS
11
HKTS 1 OM 6/27/99 11:35 PM Page 13
250 Crossways Park Drive, Woodbury, New York 11797
1-800/422-8027 (USA only) Fax: 516/682-3523
© 1999 Harman Kardon, Incorporated
“Monster Mount” is a registered trademark of Monster
Cable Products, Inc.
*Trademark of Dolby Laboratories.
Printed 6/99
1-800/422-8027 (USA only) Fax: 516/682-3523
© 1999 Harman Kardon, Incorporated
“Monster Mount” is a registered trademark of Monster
Cable Products, Inc.
*Trademark of Dolby Laboratories.
Printed 6/99
Part No. HKTS1OM
HKTS 1 OM 6/27/99 11:34 PM Page 2