DOWNLOAD Harman Kardon BDS 577 Service Manual ↓ Size: 3.81 MB | Pages: 127 in PDF or view online for FREE

Model
BDS 577
Pages
127
Size
3.81 MB
Type
PDF
Document
EMC - CB Certificate
Brand
Device
Audio
File
bds-577.pdf
Date

Harman Kardon BDS 577 EMC - CB Certificate ▷ View online

 
Page 5 of 40 
 
 
Report Ref. No.: 211-2012016-000 
 
Jiangsu TÜV Product Service Limited. - Shenzhen Branch 
 
TRF No. IEC60065K 
 
Test item particulars: 
 
Classification of installation and use ...................... :  Class II 
Supply Connection .................................................... :  AC inlet, detachable power supply cord 
Possible test case verdicts: 
 
- test case does not apply to the test object .......... :  N/A (Not Applicable) 
- test object does meet the requirement ................. :  P (Pass) 
- test object does not meet the requirement .......... :  F (Fail) 
Testing: 
 
Date of receipt of test item ........................................ :  2012-05-16 
Date (s) of performance of tests .............................. :  From 2012-05-17 to 2012-07-13 
General remarks: 
The test results presented in this report relate only to the object tested. 
This report shall not be reproduced, except in full, without the written approval of the Issuing testing 
laboratory. 
"(see Enclosure #)" refers to additional information appended to the report. 
"(see appended table)" refers to a table appended to the report. 
Throughout this report a 
 comma / 
 point is used as the decimal separator. 
Manufacturer’s Declaration per sub-clause 6.2.5 of IECEE 02: 
The application for obtaining a CB Test Certificate 
includes more than one factory location and a 
declaration from the Manufacturer stating that the 
sample(s) submitted for evaluation is (are) 
representative of the products from each factory 
has been provided ...................................................... : 
 Yes 
 Not applicable 
When differences exist; they shall be identified in the General product information section. 
Name and address of factory (ies) .......................... :  TCL Technoly Electronics (Huizhou) Co., Ltd.   
1. Section 19, Zhongkai High-tech Development 
Zone, 516006 Huizhou City, Guang Dong Province, 
PEOPLE’S REPUBLIC OF CHINA;                                     
2. TCL TECHNOLY ELECTRONICS 
(HUIZHOU) CO., LTD.   
Section 37, Zhongkai High-tech Development Zone, 
516006 Huizhou City, Guang Dong Province, 
PEOPLE’S REPUBLIC OF CHINA 
General product information: 
1. 
Blu-Ray Disc System, model No. BDS 575, BDS 275, BDS 577 and BDS 277 manufactured by 
Harman International Industries, Incorporated. USB Max. output load: 5VDC, 2.1A. 
2. 
All models are similar except output audio terminals, rated input power, wifi and airplay function, see 
below for details 
 
BDS 575 
BDS 577 
BDS 275 
BDS 277 
Audio terminals 
5ch output 
5ch output 
2ch output 
2ch output 
WIFI and Airplay 
No  
Yes  
No 
Yes 
Rated input power 
120W 
120W 
90W 
90W 
3. 
All tests were conducted on model BDS 575 which represents other models; 
4. 
The maximum operating temperature is 45
C.  
 
 
Page 6 of 40 
 
 
Report Ref. No.: 211-2012016-000 
 
 
 
 
 
 
 
 
IEC 60065 
Clause 
Requirement + Test 
 Result - Remark 
Verdict 
 
Jiangsu TÜV Product Service Limited. - Shenzhen Branch 
 
TRF No. IEC60065K 
General requirements 
 
 
Safety class of the apparatus  .................................. :  Class II 
 
4 
General test conditions 
 
4.1.4 
Ventilation instructions require the use of the test 
box  
Test box used 
 
5 
Marking and instructions 
 
 
Comprehensible and easily discernible 
 
 
Permanent durability against water and petroleum 
spirit  
 
5.1 
a) Identification, maker  ............................................. :  harman/kardon 
 
b) Model number or type reference .......................... :  BDS 575, BDS 275, BDS 577, 
BDS 277 
 
c) Class II symbol if applicable  ................................ :  Symbol according to IEC 
60417-5172 used 
 
d) Nature of supply .................................................... : 
 
 
e) Rated supply voltage  ........................................... :  100-240VAC 
 
f) Mains frequency if safety dependant  ................... :  50/60Hz 
 
g) Rated current or power consumption for 
apparatus supplied by supply apparatus for general 
use  ............................................................................ : 
 
N/A 
 
Measured current or power consumption  ............... :   
N/A 
 
Deviation % (max 10%)  ........................................... :   
N/A 
 
h) Rated current or power consumption for apparat-
us intended for connection to an a.c. mains supply . : 
120W for BDS 575, BDS 577; 
90W for BDS 275, BDS 277 
 
Measured current or power consumption  ............... :  77.9W for BDS 575, BDS 577; 
64.7W for BDS 275, BDS 277 
 
Measured current or power consumption for 
Television set  ........................................................... : 
 
N/A 
 
Deviation % (max 10%)  ........................................... :  -28.1% Max. 
5.2 
a) Earth terminal  
 
N/A 
 
b) Hazardous live terminals  
 
N/A 
 
c) Markings on supply output terminals 
 
N/A 
5.3 
a) Use of triangle with exclamation mark  
Provided in circuit diagram  
 
b) marking on loudspeaker grille, IEC 60417-5036 
 
N/A 
5.4 
Instructions for use 
Provided 
5.4.1 
 
a) Mains powered equipment not exposed to 
dripping or splashing. Warning concerning objects 
filled with liquid, etc.  
 
 
Page 7 of 40 
 
 
Report Ref. No.: 211-2012016-000 
 
 
 
 
 
 
 
 
IEC 60065 
Clause 
Requirement + Test 
 Result - Remark 
Verdict 
 
Jiangsu TÜV Product Service Limited. - Shenzhen Branch 
 
TRF No. IEC60065K 
 
 
b) Hazardous live terminals, instructions for wiring   
No such terminals 
N/A 
 
c) Instructions for replacing lithium battery  
 
N/A 
 
d) Class I earth connection warning  
 
N/A 
 
e) Instructions for multimedia system connection  
 
 
f) Special stability warning for attachment of the 
apparatus to the floor/wall  
 
N/A 
 
g) Warning: battery exposure to heat  
Batteries in remote control  
 
h) Warning: protective film on CRT face 
 
N/A 
5.4.2 
a-b) Disconnect device: plug/coupler or all-pole 
mains switch location, accessibility and markings  
AC inlet was used as 
disconnect device 
 
c) Instructions for permanently connected equipment    
N/A 
 
Marking, signal lamps or similar for completely 
disconnection from the mains  
 
N/A 
 
Hazardous radiation 
 
6.1 
Ionizing radiation < 36 pA/kg (0,5 mR/h)  
No ionizing radiation 
N/A 
 
Ionizing radiation under fault condition  
 
N/A 
6.2 
Laser radiation, emission limits to IEC 60825-1:2007
 ................................................................................... : 
Class 1  
 
Emission limits under fault conditions  ..................... :  Class 1  
 
7 
Heating under normal operating conditions 
 
7.1 
Temperature rises not exceeding specified values; 
fuse links and other protective devices defeated  
(see appended table) 
7.1.1 
Temperature rise of accessible parts  
(see appended table) 
7.1.2 
Temperature rise of parts providing electrical 
insulation  
(see appended table) 
7.1.3 
Temperature rise of parts acting as a support or as a 
mechanical barrier  
(see appended table) 
7.1.4 
Temperature rise of windings  
(see appended table) 
7.1.5 
Parts not subject to a limit under 7.1.1 to 7.1.4 
(see appended table) 
7.2 
Softening temperature of insulating material 
supporting parts conductively connected to the 
mains carrying a current > 0,2 A at least 150
 o
C  
LF501, LF502, L501, T501, 
T502 bobbin 
 
Constructional requirements with regard to the protection against electric 
shock 
 
8.1 
Conductive parts covered by lacquer, paper, 
untreated textile oxide films and beads etc. 
considered to be bare  
  
 
Page 8 of 40 
 
 
Report Ref. No.: 211-2012016-000 
 
 
 
 
 
 
 
 
IEC 60065 
Clause 
Requirement + Test 
 Result - Remark 
Verdict 
 
Jiangsu TÜV Product Service Limited. - Shenzhen Branch 
 
TRF No. IEC60065K 
8.2 
No shock hazard when changing voltage setting 
device, fuse-links or handling drawers etc.  
  
8.3 
Insulation of hazardous live parts not provided by 
hygroscopic material  
No hygroscopic material used 
N/A 
8.4 
No risk of electric shock from accessible parts or 
from parts rendered accessible following the 
removal of a cover which can be removed by hand  
 
8.5 
Class I equipment  
Class II equipment 
N/A 
 
Basic insulation between hazardous live parts and 
earthed accessible parts  
 
N/A 
 
Resistors bridging basic insulation complying with 
14.1 a)  
 
N/A 
 
Capacitors bridging basic insulation complying with 
14.2.1 a)  
 
N/A 
 
Protective earthing terminal  
 
N/A 
8.6 
Class II equipment and Class II constructions within 
Class I equipment  
Class II equipment  
 
Double or reinforced insulation between hazardous 
live parts and accessible parts  
 
 
Components bridging double or reinforced insulation 
complying with 14.1 a) or 14.3  
Isolating transformer T501 and 
T502 used  
 
Basic insulation bridged by components complying 
with 14.3.4.3.  
 
N/A 
 
Basic and supplementary insulation each being 
bridged by a capacitor complying with 14.1 a)  
 
N/A 
 
Double or reinforced insulation being bridged with 2 
capacitors in series complying with 14.2.1 a)  
 
N/A 
 
Double or reinforced insulation being bridged with a 
single capacitor complying with 14.2.1 b)   
Approved Y1-cap. (CY501, 
CY502, CY504, CY506) used 
8.7 
This clause is void  
 
— 
8.8 
Basic or supplementary insulation > 0,4 mm (mm) : 
T501 Bobbin: min. 1.0mm 
 
Reinforced insulation > 0,4 mm (mm)  .................... : 
T502 Bobbin: min. 0.9mm 
 
Thin sheet insulation (excluding non-separable thin 
sheet insulation. See 8.22)  
 
 
Basic or supplementary insulation, at least two 
layers, each meeting 10.3  
 
N/A 
 
Basic or supplementary insulation, three layers any 
two of which meet 10.3  
 
N/A 
 
Reinforced insulation, two layers each of which meet 
10.3  
Insulation tape wrapped in 
T501. 
 
Page of 127
Display

Click on the first or last page to see other BDS 577 service manuals if exist.