DOWNLOAD Harman Kardon AVR 7000 Service Manual ↓ Size: 11.35 MB | Pages: 104 in PDF or view online for FREE

Europe Mono 40kHz  Stereo 67.5kHz  Pilot 7

America Mono 75kHz  Stereo 40kHz Pilot 7.5k

 Local OSC

 Frequency cover ra

 Standard supply vo

 FM Antenna input I

 AM  Loop Antenna 

 AF Output Le

 Auto Stop Sens.

 Stereo Separ 1kHz

 AF Output Le

 Auto Stop Sens.

FM

47• Load

•98.0

•98.1

60

•98.0

•98.1

--

•98.0

•98.1

60

on Adjus

MW

47• Load

•999

•1000

74

--

uV/m

30

165±50

•999 

•1000

mV

30

800±6

1-1

1-2

1-3

1-4

TEST 

CONDITION

Above the receiving Frequency

15.0 (+/-1.5V)

75 ohm             

18uH  ( 50 ohm )

pecificati

T.P.

dBu

40 min

•40

•75

kHz,%

NO

TEST  ITEMS

MOD.

T.L.

•40

•75

500±100

mV

33.2 ±6

SVR3

SVR1

1-5

djustment

on Adjus

dBf

SVR2

UNIT

dB

M   W

F     M

•522 ~ 1620kHz

•520 ~ 1720kHz

•87.5 ~ 108.0MHz

•87.5 ~ 107.9MHz

TROUBLESHOOTING GUIDE

Unit does not function when Main

• No AC Power

• Make certain AC power cord is plugged into 

Power Switch is pushed

a live outlet

• Check to see if outlet is switch-controlled

Display lights, but no sound

• Intermittent input connections

• Make certain that all input and speaker connections 

or picture

• Mute is on

are secure

• Volume control is down

• Press Mute button
• Turn up volume control

Unit turns on, but Front-Panel 

• Display brightness is turned off

• Follow the instructions in the Display Brightness section 

Display does not light up

on page 31 so that the display is set to VFD FULL

No sound from any speaker;

• Amplifier is in protection mode 

• Check speaker wire connections for shorts at receiver and 

Light around power switch is red

due to possible short

speaker ends 

• Amplifier is in protection mode 

• Contact your local Harman Kardon service depot

due to internal problems

No sound from surround or

• Incorrect surround mode

• Select a mode other than Stereo

center speakers

• Input is monaural

• There is no surround information from mono sources

• Incorrect configuration 

• Check speaker mode configuratioin                                       

• Stereo or Mono program material

• The surround decoder may not create center or rear channel 

information from nonencoded programs

Unit does not respond to

• Weak batteries in remote

• Change remote batteries

remote commands

• Wrong device selected

• Press the AVR selector

• Remote sensor is obscured

• Make certain front panel sensor is visible to remote

or connect remote sensor

Intermittent buzzing in tuner

• Local interference

• Move unit or antenna away from computers, fluorescent 

lights, motors or other electrical appliances

Letters flash in the Channel Indicator

• Digital audio feed paused

• Resume play for DVD

Display and Digital Audio stops

• Check that Digital Input is selected

HDCD encoded disc does not trigger

• Surround mode in use

• Select “Surround Off” mode

HDCD indicator

• Analog feed in use

• Connect and select digital connection to CD player

In the rare case where the unit’s operation or
the displays seem abnormal, the cause may
involve the erratic operation of the system’s
memory or microprocessor.

To correct this problem, first unplug the unit
from the AC wall outlet and wait at least three
minutes. After the pause, reconnect the AC
power cord and check the unit’s operation. If
the system still malfunctions, a system reset
may clear the problem.

To clear the AVR 7000’s entire system memory
including tuner presets, output level settings,

delay times and speaker configuration data,
first put the unit in Standby by pressing the
System Power Control button 

2. Next,

press and hold the Tone Mode

6 and the

@ buttons for three 

seconds.

The unit will turn on automatically and display
the RESET message in the Main
Information Display 

W. Note that once you

have cleared the memory in this manner, it is
necessary to re-establish all system configuration
settings and tuner presets.

NOTE: Resetting the processor will erase any
configuration settings you have made for

speakers, output levels, surround modes, digital
input assignments as well as the tuner presets.
After a reset the unit will be returned to the
factory presets, and all settings for these items
must be reentered.

If the system is still operating incorrectly, there
may have been an electronic discharge or
severe AC line interference that has corrupted
the memory or microprocessor.

If these steps do not solve the problem, consult
an authorized Harman Kardon service depot.