DOWNLOAD Harman Kardon AVR 158 (serv.man5) Service Manual ↓ Size: 4.13 MB | Pages: 111 in PDF or view online for FREE

Reference No. : 54121101A                                                                                                                  Page 4/50

 

◀  Anam EMC Test Laboratory  ▶

 

 
1. CLIENT INFORMATION 

 

The EUT has been tested by request of: 

* Company 

: Harman Consumer Group 

 

  8500 Balboa Blvd., Northridge, CA 91329, USA 

* Contact Person 

: 

Mr. Tim Huang (Sr Compliance   Engineer) 

   

 

Mr. Aaron Butters

 

* Tel. 

: 

+86 755 8634 3778 / +1 818 895 3312

 

 

2. EQUIPMENT UNDER TEST (EUT) 

2.1. Identification of the EUT 

*Equipment AV 

Receiver 

*Model No. 

AVR158/230, AVR156/230(Alt) 

*Brand Name 

Harman/Kardon 

*Serial No. 

N/A 

*Manufacturer 
 (China) 

DongGuan LiaoBu Anam Electronics 
Xin Cheng Management Area, Liaobu Town, 
Dongguan City, Guang Dong Province, China 
Fax: 86-769-3216338  Tel: 86-769-3326888 

*Power Rating 

AC 230V~, 50Hz,   

*Tuner Section 

FM 87.5 ㎒ ~ 108 ㎒   
AM 522 ㎑ ~ 1,620 ㎑ 
 

*External signal 
 In/Out terminal 

SPEAKER L/R/SL/SR/C 
PHONES 
AUDIO(AUX1, CD, TAPE IN/OUT, VIDEO 1 
                VIDEO 2 IN/OUT, DVD, AUX 2) 
COAXAIL, OPTICAL 1,2 
SUBWOOFER OUT 
COMPONENT VIDEO 
COMPOSITE(VIDEO 1, 2 IN/OUT, DVD, MONITOR OUT) 
TRIGGER OUT 
HDMI 1,2,3, OUT 
USB(Only service update) 

 
2.2. Additional Information about the EUT 

The EUT consists of the following Subsystems/Modules/Parts: N/A 

 

The test have been performed on the EUT provided with the following 

              modifications : None. 

 
 
 

Reference No. : 54121101A                                                                                                                  Page 5/50

 

◀  Anam EMC Test Laboratory  ▶

 

 
3. TEST SPECIFICATIONS 

 

   3.1. Standards 
 

*EN55013 (2001)&A1(2003)+A2(2006) : 

Sound and Television broadcast receivers and Associated equipment 
-Radio Disturbance characteristics - Limits and methods of measurement. 

 * 

EN61000-3-2(2006): 

Part 3-2: Limits- Limits for harmonic current emissions 
 

(Equipment input current  ≤16A per phase) 

 *EN61000-3-3(2008): 
 

 Part 3-3: Limits- Limitation of voltage changes, voltage fluctuations and 
flicker in public low-voltage supply systems for equipment with rated 
current  ≤16A. 

      3.2. Additions, deviations and exclusions from standard 
 

No additions, deviations or exclusions have been made from standard. 

 
      3.3. Purpose of the test: 
 

To determine whether the EUT fulfils the EMC-emission requirements of the   

 

Standards stated in section 3.1. 

 
      3.4. Mode of operation during the test 
 

The EUT was operated in such a way as to deliver one-eighth on the non-clipped 

 

output power to the rated load impedance using the sinusoidal of 1 ㎑ & color- 

       bar. 
 

The EUT was set to the mode of Tuner. 

 

4. TEST SUMMARY 

 

The results in this report apply only to sample(s) tested: 

Test item 

Passed 

the test 

Note 

Mains terminal disturbance voltage 

Yes 

 

Disturbance Radiation 

Yes 

 

Antenna Terminal Disturbance Voltage 

Yes 

 

Disturbance Power 

Yes 

 

Harmonics Yes 

 

Flicker Yes 

 

 

The equipment does comply with the requirements. 

 

For the measurement data, see Annex. 

 

Reference No. : 54121101A                                                                                                                  Page 6/50

 

◀  Anam EMC Test Laboratory  ▶

 

 

5. MAINS TERMINAL DISTURBANCE VOLTAGE IN THE FREQUENCY 

RANGE 0.15MHz TO 30MHz

 

 

   5.1. Operating environment 

Temperature 

: 15℃ 

Relative humidity  : 33 % 

 

5.2. Test set-up and procedure 

 

 

 

The mains terminal disturbance voltage was measured with the EUT in a 
Screened room. The EUT was placed on a non-metallic table by 0.8m above   
the metallic grounded floor and 0.4m from the reference ground panel (RGP) 
wall. The distance to other metallic surfaces was at least 0.8m. 
The EUT was tested with the outer conductor of the antenna input connected 
as well as not connected to the ground terminal of the AMN. 
The level of the test signal was 500mV (1 KHz) at coaxial RF input connector. 
Amplitude measurements were performed with a quasi-peak detector and, 
If required, with an average detector. 

 
5.3. Measurement uncertainty 

 

Mains terminal disturbance voltage, quasi-peak detection:  ±2.0dB 

 

Mains terminal disturbance voltage, average detection      :  ±2.0dB 

 

The measurement uncertainty describes the overall uncertainty of the given 

 

measured value during the operation of the EUT in the above-mentioned way. 

 
 
 
 
 
 

Reference No. : 54121101A                                                                                                                  Page 7/50

 

◀  Anam EMC Test Laboratory  ▶

 

 

5.4. Test instrument 

Equipment 

Manufacturer 

Type No. 

Serial No. 

Test site 

Shielded room 

- 

- 

Measurement 
                      Receiver 

R & S 

ESCI 

100348 

Artificial mains 
                      Network 

R & S 

ESH3-Z5 

844249/020 

EMCO 3825/2 90101718 

Test Compact Disc 

Abex 

TCD-782 

N/A 

R. C. Oscillator 

Kenwood 

AG-203A 

3090241 

Signal Generator 

Anritsu 

MG3632A 

MT79870 

 

* R & S: Rohde & Schwarz 

 

5.5. Test protocol 

 

 

Date: January 19, 2010 

 

Grounded at the Signal GND Terminal on the Rear Enclosure. 

 

An overview sweep performed with peak detector is included in the test 
report as Annex A. 

Mode 

Freq. 

(㎒) 

Quasi-peak (㏈㎶) Average 

(㏈㎶) 

Limit 

Disturbance value 

Limit 

Disturbance value 

Line 1 

Line 2 

Line 1 

Line 2 

Tuner .154 65.9 41.3 40.5 55.9 17.5 17.4 

 

 

 

 

 

 

 

 

 

 
Ungrounded at the Signal GND Terminal on the Rear Enclosure. 

 

An overview sweep performed with peak detector is included in the test 
report as Annex A 

Mode 

Freq. 

(㎒) 

Quasi-peak (㏈㎶) Average 

(㏈㎶) 

Limit 

Disturbance value 

Limit 

Disturbance value 

Line 1 

Line 2 

Line 1 

Line 2 

Tuner .154 65.9 41.1 41.0 55.9 17.6 17.2 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CD  .154 65.9 41.4 41.0 55.9 17.9 17.7 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The equipment does comply with the requirements. 

 

For the measurement data, see Annex A (6 Copies).