Harman Kardon AVR 147 Service Manual ▷ View online
NO
DESCRIPTION
PARTS NO.
Q,ty
1
2
3
4
5
1
1. Instruction manual ass'y - Accessories
2. Package Drawing
7
1
1
AVR147/230
FM 1 POL ANT
CSA1A018Z
1
NO
DESCRIPTION
PARTS NO.
Q,ty
9
10
11
12
13
1
CPB1061W
POLY BAG
CQX1A1254Z
MANUAL,INSTRUCTION
MANUAL ,SETUP GUIDE
1
1
BOOKLET,INFORMATION
CQE1A180Z
1
STAPLE
CPL0905
3
ACCESSORY-2
ACCESSORY-1
CPB1061W
POLY BAG
CSA1A027Z
AM LOOP ANTENNA ASS'Y
1
CABR03P3
BATTERY
3
COVER ASS'Y
CGRAVR130/230ZA
POLY BAG
1
12
7
2
3
AM LOOP ANTENNA ASS'Y
BATTERY ASS'Y
4
FM 1 POLE ANT
5
COVER ASS'Y
6
BOOKLET,INFORMATION
9
MANUAL INSTRUCTION
10
MANUAL SETUP CODE
11
1
1
CGR1A332M7H43
CQE1A220Z
CPS1A676
1
CPB1A176Z
1
1
2
3
4
5
CGR1A331M7H43
1
PAD , COVER
COVER A
COVER B
SHEET,FRONT COVER
BAG , POLY
CQX1A1256Z
13
1
IMAGE BROCHURES
HQE1A273Z
IMAGE BROCHURES
STAPLE
POLY BAG
REMOCON
TRANSMITTER ASS'Y
6
STAPLE
8
8
STAPLE
CPL0905
3
REMOCON ASS'Y
CARTAVR147/230
1
ACCESSORY-1
BOX,OUT CARTON
3
4
1
DESCRIPTION
NO
CPS5A564
CQXAVR147/230
CPG1A822V
1
1
1
Q,ty
PARTS NO.
CPS5A565
SNOW,PAD(R)
2
1
SNOW,PAD(L)
SET
AVR147/230SET
1
5
ACCESSORY-2
6
CQXAVR147/230
1
SNOW PAD (R)
3
BOX ,OUT CARTON
5
SET
4
SNOW PAD (L)
2
MICROPHONE ASS'Y
8
ACCESSORY-2
7
MICROPHONE ASS'Y
7
CJXAVR340MICRO
1
MICROPHONE ASS'Y
A
A
MICROPHONE ASS'Y
CJXAVR340MICRO
1
ACCESSORY-1
1
harman/kardon
AVR147/230 Service Manual
Page 5 of 124
1
2
1
1. Removing the Top Cabinet
Remove the Screws
5
4
6
DISASSEMBLY
~
13
11
10
7
9
13
3
12
8
7
5
6
8
9
4
3
2
1
Remove the Screws
2. Removing the Front Panel
1
9
~
6
3
4
7
Remove the Screws
4. Removing the Main PCB
1
2
5
~
1
7
~
1
28
Remove the Screws
3. Removing the Rear Panel
AVR147/230
28
10
9
8
22
7
6
5
23
24 25
19
18
4
3
2
1
20
21
26
27
14 15
16 17
13
12
11
harman/kardon
AVR147/230 Service Manual
Page 6 of 124
Harman Kardon AVR 147
DISASSEMBLY PROCEDURES
<1> TOP-CABINET(21) REMOVAL
1. Remove 13 screws(S1,S7) and then remove the Top-cabinet.
<2> FRONT PANEL ASS’Y REMOVAL
1. Remove the Top-cabinet, referring to the previous step<1>.
2. Disconnect the card cable between connector(CN72-17p) on the Fip PCB(37-1)
and connector(CN72) on the Input PCB(39-1).
3. Disconnect the lead wire(BN81-8P) on the Fip PCB(37-1) from connector(CN81) on the Trans PCB(40-4).
4. Disconnect the lead wire(BN22-6P) on the Phone PCB(37-5) from connector(CN22) on the Input PCB(39-1).
5. Disconnect the lead wire(BN18-5P) on the Phone PCB(37-5) from connector(CN18) on the Input PCB(39-1).
6. Disconnect the lead wire(BN10-4P) on the Volume PCB(37-6) from connector(CN10) on the Input PCB(39-1).
7. Disconnect the lead wire(BN51-2P) on the Volume PCB(37-6) from connector(CN51) on the Input PCB(39-1).
8. Disconnect the lead wire(BN41-6P) on the Volume PCB(37-6) from connector(CN41) on the Video PCB(41).
9. Disconnect the lead wire(BN90-2P) on the Main PCB(38-1) from connector(CN86) on the Moms PCB(37-4).
10. Remove 1 screw(S10) and then lead wire(JW82-1P,JW83-1P) on the Phone PCB(37-5).
11 .Remove 1screw(S10) and then lead wire(JW84-1P) on the Volume PCB(37-3).
12. Remove 10 screws(S1) and then remove the Front Panel ASS’Y.
<3> Volume PCB(37-6) REMOVAL
1. Remove the Top-cabinet, referring to the previous step<1>.
2. Remove the Front Panel ASS’Y, referring to the previous step<2>.
3. Pull out the Volume Knob ASS’Y.
4. Disconnect connector(CN84) on the Volume PCB(37-6) from the lead wire(BN84-5P) on the Fip PCB(37-1).
5. Disconnect the lead wire(BN92-5P)on the Volume PCB(37-6) from connector(CN92) on the Phone PCB(37-5).
6. Remove 8 screws(S2,S14), and then remove the Volume PCB(37-6).
<4>PHONE PCB(37-5) REMOVAL
1. Remove the Top-cabinet, referring to the previous step<1>.
2. Remove the Front Panel ASS’Y, referring to the previous step<2>.
3. Disconnect connector(CN85)on the Phone PCB(37-5) from the lead wire(BN85-3P) on the Fip PCB(37-1).
4. Disconnect the lead wire(BN92-5P)on the Volume PCB(37-6) from connector(CN92) on the Phone PCB(37-5).
5. Remove 2 screws(S2) and then remove the Phone PCB(37-5).
.
<5>POWER LED PCB(37-3) REMOVAL
1. Remove the Top-cabinet, referring to the previous step<1>.
2. Remove the Front Panel ASS’Y, referring to the previous step<2>.
3. Disconnect connector(CN88) on the Power Led PCB(37-3) from the lead wire(BN88-4P) on the Fip PCB(37-1) .
4. Remove 2 screws(S2) and then remove the Power led PCB(37-3).
<6>FIP PCB(37-1) REMOVAL
1. Remove the Top-cabinet, referring to the previous step<1>.
2. Remove the Front Panel ASS’Y, referring to the previous step<2>.
3. Disconnect the lead wire(BN84-5P) on the Fip PCB(37-1) from connector(CN84) on the Volume PCB(37-6).
harman/kardon
AVR147/230 Service Manual
Page 7 of 124
4. Disconnect the lead wire(BN85-3P) on the Fip PCB(37-1) from connector(CN85) on the Phone PCB(37-5).
5. Disconnect the lead wire(BN88-4P) on the Fip PCB(37-1) from connector(CN88) on the Power Led PCB(37-3).
6. Disconnect the connector (CN89) on the Fip PCB(37-1) from lead wire(BN89-4P) on the Key PCB(37-2).
7. Remove 3 screws(S2) and then remove the Guide PCB(37-8) & the Fip PCB(37-1).
<7>KEY PCB(37-2) REMOVAL
1. Remove the Top-cabinet, referring to the previous step<1>.
2. Remove the Front Panel ASS’Y, referring to the previous step<2>.
3. Remove the Fip PCB(37-1), referring to the previous step<6>.
4. Remove 10 screws(S2) and then remove the Key PCB(37-2).
<8>TUNER MODULE(44) REMOVAL
1. Remove the Top-cabinet, referring to the previous step<1>.
2. Disconnect the card cable between connector(CON1-13P) on the Tuner module(42)
and connector(CN13) on the Input PCB(39-1).
3. Remove 2 screws(S8) and then remove the Tuner Module(43).
<9>VIDEO PCB(41) REMOVAL
1. Remove the Top-cabinet, referring to the previous step<1>.
2. Disconnect the card cable between connector(BN14-13P) on the Video PCB(41)
and connector(CN14) on the Input PCB(39-1).
3. Disconnect connector(CN43) on the Video PCB(41)
from the lead wire(BN43-3P) on the Regulator PCB(A)(40-2).
4. Disconnect the card cable between connector(CN42) on the Video PCB(41).
and connector(BN44-7P) on the iPod PCB(39-2).
5. Disconnect connector(CN41) on the Video PCB(41) from the lead wire(BN41-6P) on the Volume PCB(37-6).
6. Remove 6 screws(S8) and then remove the Video PCB(41).
<10>iPod PCB(39-2) REMOVAL
1. Remove the Top-cabinet, referring to the previous step<1>.
2. Remove the Video PCB(41), referring to the previous step<9>
3. Disconnect the card cable between connector(BN19-15P) on the the iPod PCB(39-2)
and connector(CN19) on the Input PCB(39-1).
4. Disconnect the card cable between connector(BN44-7P) on the iPod PCB(39-2)
and connector(CN42) on the Video PCB(41).
5. Disconnect the card cable between connector(CN47-7P) on the iPod PCB(39-2)
and connector(CN47) on the RS232 PCB(37-7).
6. Disconnect the board to board connector between and connector(CN23) on the XM PCB(42)
and connector(BN17-12P) on the iPod PCB(39-2).
7. Remove 2 screws(S13) and then remove the iPod PCB(39-2).
<11>XM PCB(42) REMOVAL
1. Remove the Top-cabinet, referring to the previous step<1>.
2. Remove the Video PCB(41), referring to the previous step<9>.
3. Disconnect the card cable between connector(BN21-7P) on XM PCB(42)
and connector(CN21) on the input PCB(39-1).
4. Disconnect the lead wire(BN85-2P) on the XM PCB(42) from connector(CN85) on the Regulator PCB(A)(40-2).
5. Disconnect the board to board connector between and connector(CN23) on the XM PCB(42)
and connector(BN17-12P) on the iPod PCB(39-2).
6. Remove 1 screws(S15) and then remove the XM PCB(42).
<12>HDMI PCB(47) REMOVAL
1. Remove the Top-cabinet, referring to the previous step<1>.
harman/kardon
AVR147/230 Service Manual
Page 8 of 124
Click on the first or last page to see other AVR 147 service manuals if exist.