DOWNLOAD Harman Kardon AVR 135 (serv.man4) Service Manual ↓ Size: 1008.56 KB | Pages: 42 in PDF or view online for FREE

TUNER OPERATION 33

The AVR 135’s tuner is capable of tuning AM, FM
and FM Stereo broadcast stations and receiving
RDS data. Stations may be tuned manually, or
they may be stored as favorite station presets and
recalled from a 30 position memory.

1. Press the AM/FM Tuner Select button 

6

on the remote to select the tuner as an input. The
tuner may be selected from the front panel by
either pressing the Input Source Selector %
until the tuner is active or by pressing the Tuner
Band Selector ! at any time.

2. Press the AM/FM Tuner Select button 

6 or

Tuner Band Selector ! again to switch
between AM and FM so that the desired 
frequency band is selected.

3. Press the Tuner Mode button 

I on the

remote or hold the Band Selector ! on the
front panel pressed for 3 seconds to select 
manual or automatic tuning.

When the button is pressed so that 

AUTO

appears in the Main Information Display ˜
each press of the Tuning Selectors 8

J will

put the tuner in a scan mode that seeks the next
higher or lower frequency station with acceptable
signal strength. An 

AUTO S T TUNED

indica-

tion will momentarily appear when the station
stops at a stereo FM station, and an 

AUTO

TUNED

indication will momentarily appear

when an AM or monaural FM station is tuned.
Press the Tuning buttons again to scan to the
next receivable station.

When the button is pressed so that 

MANUAL

appears in the Main Information Display ˜
each tap of the Selector will increased or
decrease the frequency by one increment. When
the tuner receives a strong enough signal for
adequate reception,

MANAUL TUNED

will

appear in the Main Information Display ˜.

4. Stations may also be tuned directly by pressing
the Direct button 

J, and then pressing the

H that correspond to the sta-

tion’s frequency. Note that for entering numbers
higher than 100 you need to enter only the "1"
rather than "10", the first "0" will be added
automatically. The desired station will automati-
cally be tuned after the latest number is entered.
If you press an incorrect button while entering a
direct frequency, press the Clear button 

# to

start over.

NOTE: When the FM reception of a stereo station
is weak, audio quality will be increased by
switching to Mono mode by pressing the Tuner
Mode button 

I on the remote or holding the

Band Selector ! on the front panel so that

MANUAL

appears momentarily in the Main

Information Display ˜ and then goes out.

Preset Tuning
Using the remote, up to 30 stations may be
stored in the AVR’s memory for easy recall using
the front panel controls or the remote.

To enter a station into the memory, first tune the
station using the steps outlined above. Then:

1. Press the Memory button 

$ on the remote.

Note that two underscore lines will appear in the
Main Information Display ˜.

2. Within five seconds, press the Numeric 
Keys

H corresponding to the location where

you wish to store this station’s frequency. Once
entered, the preset number will appear in the
Main Information Display ˜.

3. Repeat the process after tuning any additional
stations to be preset.

Recalling Preset Stations
• To manually select a station previously entered
in the preset memory, press the Numeric Keys
H that correspond to the desired station’s
memory location.

• To manually tune through the list of stored pre-
set stations one by one, press the Preset
Stations Selector buttons #

" on the front

panel or remote.

The AVR 135 is equipped with RDS (Radio Data
System), which brings a wide range of informa-
tion to FM radio. Now in use in many countries,
RDS is a system for transmitting station call signs
or network information, a description of station
program type, text messages about the station or
specifics of a musical selection, and the correct
time.

As more FM stations become equipped with RDS
capabilities, the AVR will serve as an easy-to-use
center for both information and entertainment.
This section will help you take maximum advan-
tage of the RDS system.

RDS Tuning
When an FM station is tuned in and it contains
RDS data, the AVR will automatically display the
station’s call sign or other program service in the
Main Information Display ˜.

RDS Display Options
The RDS system is capable of transmitting a wide
variety of information in addition to the initial
station call sign that appears when a station is
first tuned. In normal RDS operation the display
will indicate the station name, broadcast net-
work or call letters. Pressing the RDS button
^

! enables you to cycle through the various

data types in the following sequence:

• The station’s call letters (with some private
stations other information too).

• The station’s frequency (

FREQ

).

• The Program Type (

PTY

) as shown in the list

below.

NOTE: Many stations do not transmit a specific
PTY. The display will show 

NONE

, when such a

station is selected and PTY is active.

• A “text” message (Radiotext,

R T

) containing

special information from the broadcast station.
Note that this message may scroll across the
display to permit messages longer than the eight
positions in the display. Depending on signal qual-
ity, it may take up to 30 seconds for the text mes-
sage to appear; in that time, the word 

TEXT

will

flash in the Information Display when RT is select-
ed.

• The current time of day (

C T

). Note that it may

take up to two minutes for the time to appear, in
that time the word 

TIME

will flash in the infor-

mation display when CT is selected. Please note
that the accuracy of the time data is dependent
on the radio station, not the AVR.

34 TUNER OPERATION

Some RDS stations may not include some of
these additional features. If the data required for
the selected mode is not being transmitted, the
Main Information Display ˜ will show a

N O TYPE

,

N O TEXT

or 

N O TIME

message after the individual time out.

In any FM mode the RDS function requires a
strong enough signal for proper operation.

Program Search (PTY)
An important feature of RDS is its capability of
encoding broadcasts with Program Type (PTY)
codes that indicate the type of material being
broadcast. The following list shows the
abbreviations used to indicate each PTY, along
with an explanation of the PTY:

• (RDS ONLY)

• (TRAFFIC)

• NEWS: News

• AFFAIRS: Current Affairs

• INFO: Infomation

• SPORT: Sports

• EDUCATE: Educational

• DRAMA: Drama

• CULTURE: Culture

• SCIENCE: Sciencek

• VARIED: Varied Speech Programs

• POPM: Popular Music

• ROCKM: Rock Music

• M.O.R.M.: Middle-of-the-Road Music

• LIGHTM: Classical Music

• CLASSICS: Serious Classical Music

• OTHERM: Other Music

• WEATHER: Weather Information

• FINANCE: Financial Programs

• CHILDREN: Children’s Programs

• SOCIAL A: Social Affairs Programs

• RELIGION: Religious Broadcasts

• PHONE IN: Phone-In Programs

• TRAVEL: Travel and Touring

• LEISURE: Leisure and Hobby

• JAZZ: Jazz Music

• COUNTRY: Country Music

• NATIONAL: National Music

• OLDIES: Oldies Music

• FOLK M: Folk Music

• DOCUMENT: Documentary Programs

• TEST: Emergency Test

• ALARM: Emergency Broadcast Information

You may search for a specific Program Type (PTY)
by following these steps:

1. Press the RDS button ^

! until the 

current PTY is shown in the Main Information
Display ˜.

2. While the PTY is shown, press the Preset
Up/Down button #

" or hold them pressed

to scroll through the list of available PTY types,
as shown above starting with the PTY currently
received. To simply search for the next station
transmitting any RDS data, use the Preset
Up/Down button #

" until 

RDS ONLY

appears in the display.

3. Press any of the Tuning Up/Down buttons
)

K, the tuner begins to scan the FM band

upwards or downwards for the first station that
has RDS data that matches the desired 
selection, and acceptable signal strength for
quality reception.

4. The tuner will make up to one complete scan
of the entire FM band for the next station that
matches the desired PTY type and has accept-
able reception quality. If no such station is
found, the display will read 

NONE

for some

seconds and the tuner will return to the last FM
station in use before the search.

NOTE: Some stations transmit constant traffic
information. These stations can be found by
selecting 

TRAFFIC

, the option in front of

NEWS

in the list. The AVR will find the next

appropriate station, even if it is not broadcasting
traffic information when the search is made.

PROGRAMMING THE REMOTE  35

The AVR 135 is equipped with a powerful remote
control that will control not only the receiver’s
functions, but also most popular brands of audio
and video equipment, including CD players, TV
sets, cable boxes, VCRs, satellite receivers and
other home-theater equipment. Once the AVR’s
remote is programmed with the codes for the
products you own, it is possible to eliminate most
other remotes and replace them with the con-
venience of a single universal remote control.

As shipped from the factory, the remote is fully
programmed for all AVR functions, as well as those
of most Harman Kardon CD changers, DVD
players, CD players and cassette decks. In addition,
by following one of the methods below, you may
program the remote to operate a wide range of
devices from other manufacturers.

Direct Code Entry 
This method is the easiest way to program your
remote to work with different products.

1. Use the tables in the separate setup-code
guide to determine the three-digit code or codes
that match both the product type (e.g., VCR, TV),
and the specific brand name. If there is more than
one number for a brand, make note of the
different choices.

2. Turn on the unit you wish to program into the
AVR remote.

3. Press and hold both the Input Selector

4

for the type of product to be entered (e.g., VCR,
TV) and the Mute

button 

( at the same

time. When the Program/SPL Indicator

2

turns amber and begins flashing, release the
buttons. It is important that you begin the next
step within 20 seconds.

4. If the unit you wish to program into the 
AVR remote has a remotable Power on/off func-
tion, follow these steps:

a. Point the AVR’s remote towards the unit to be

programmed, and enter the first three-digit code
number using the Numeric buttons 

H. If the

unit being programmed turns off, the correct
code has been entered. Press the Input
Selector

4 again, and note that the red light

under the Input Selector will flash three times
before going dark to confirm the entry.

b. If the product to be programmed does NOT

turn off, continue to enter the three-digit code
numbers until the equipment turns off. At this
point, the correct code has been entered. Press
the Input Selector

4 again and note that

the red light under the Input Selector will
flash three times before going dark to confirm
the entry.

5. If the Power function of the unit to be pro-
grammed cannot be remoted, follow these steps
(max. 20 seconds after step 3 above, or else step
3 must be repeated first):

a. Enter the first three-digit code number using

the Numeric buttons 

H and press the Input

4 again. Press the remote button

of any transport function remotable with the
unit, e.g. Pause or Play

fl

P. If the unit

being programmed starts that function, the
correct code has been entered.

b. If the unit does not start the function whose

button was pressed, repeat steps 3 and 5a
above with the next three-digit code number
listed in the setup code table for that brand
and product type, until the unit reacts properly
on the transport function transmitted.

6. Try all of the functions on the remote to make
certain that the product operates properly. Keep
in mind that many manufacturers use a number
of different combinations of codes, so it is a good
idea to make certain that not only does the
Power control work, but that the volume, channel
and transport controls work as they should. If
functions do not work properly, you may need to
use a different remote code.

7. If the unit does not react to any code
entered, if the code for your product does not
appear in the tables in the separate setup-code
guide, or if not all functions operate properly, try
programming the remote with the Auto Search
Method.

Note on Using the AVR remote with a
Harman Kardon CD Recorder.
As shipped from the factory. the remote is
programmed for controlling Harman Kardon CD
players. It can also control most functions of the
Harman Kardon CD-Recorders (see function list
on page 40) too after the code ”002” is entered
on the CD Selector button 

4 as described

above. For returning to the CD player control
commands the code ”001” must be entered.

Auto-Search Method
If the unit you wish to include in the AVR’s
remote is not listed in the code tables in the sep-
arate setup-code guide or if the code does not
seem to operate properly, you may wish to pro-
gram the correct code using the Auto Search
method that follows. Note that the Auto Search
method works only with units whose Power func-
tions can be remoted:

1. Turn on the product that you wish to include in
the AVR remote.

2. Press and hold both the Input Selector

4

for the type of product to be entered (e.g., VCR,
TV) and the Mute

button 

( at the same

time. When the Program/SPL Indicator

2

turns amber and begins flashing, release the
buttons. It is important that you begin the next
step within 20 seconds.

3. To find out if the code for your unit is pre-pro-
grammed, point the AVR remote towards the unit
to be programmed, and press and hold the 

⁄

but-

ton

D.This will send out a series of codes from

the remote’s built-in data base, with each flash of
the red light under the Input Selector

4 indi-

cating that a code has been sent. When the device
to be programmed turns off,immediately release
the 

⁄

button

D. Note that it may take one

minute or more until the right code is found and
the unit turns off.

4. When the 

⁄

button was not released in time

after the unit turned off, the proper code will be
”overrun”. That’s why a function test should be
made: Turn the unit on again and, while the
Input Selector

4 still lights red, press the 

⁄

button

D once, than the 

¤

button 

D once

too. When the unit turns off, the right code was
found, when not, the code was ”overrun”. To re-
find the correct, while the Input Selector

4

still lights red, press (not hold pressed) the 

¤

button 

D repeatedly to step backwards

through the codes available and observe the
reaction of the unit at each press. As soon as the
unit turns off the correct code is found.

5. Press the Input Selector

4 again, and note

that the red light will flash three times before
going dark to confirm the entry.

6. Try all of the functions on the remote to make
certain that the product operates. Keep in mind
that many manufacturers use a number of differ-
ent combinations of codes, and it is a good idea
to make certain that not only the Power control
works, but the volume, channel and transport
controls, as appropriate. If all functions do not
work properly, you may need to Auto-Search for a
different code, or enter a code via the Direct
Code Entry method.

When the code has been entered using the Auto
Search method, it is always a good idea to find
out the exact code so that it may be easily reen-
tered if necessary. You may also read the codes to
verify which device has been programmed to a
specific Control Selector button.

1. Press and hold both the Input Selector

4

for the device you wish to find the code for and
the Mute button 

( at the same time. Note

that the Program/SPL Indicator

2 will

initally turn amber and begin flashing. Release
the buttons and begin the next step within 
20 seconds.

2. Press the Set button 

F. The Program/SPL

2 will then blink green in a

sequence that corresponds to the three-digit
code, with a one-second pause between each
digit. Count the number of blinks between each
pause to determine the digit of the code. One
blink is the number 1, two blinks is the number
2, and so forth. Note that a rapid sequence of
three blinks is used to indicate a “0.”

Example: One blink, followed by a one-second
pause, followed by six blinks, followed by a one-
second pause, followed by four blinks indicates
that the code has been set to 164.

36 PROGRAMMING THE REMOTE

For future reference enter the Setup Codes for the
equipment in your system here:

Macros enable you to easily repeat frequently
used combinations of commands with the press of
a single button on the AVR’s remote control. Once
programmed, a macro will send out up to 19 dif-
ferent remote codes in a pre-determined sequen-
tial order enabling you to automate the process of
turning on your system, changing devices, or other
common tasks. The AVR’s remote can store up to
five separate macro command sequences, one
that is associated with the Power On button
3, and four more that are accessed by pressing
the Macro buttons 

 .

1. To start programming a macro, press the Mute
button 

( and the Macro button   to be

programmed or the Power-On button

3 at the

same time. Note that the latest selected Input
Selector will light red, and the Program/SPL
Indicator

2 will flash amber.

2. Enter the steps for the macro sequence by
pressing the button for the actual command step.
Although the macro may contain up to 19 steps,
each button press, including those used to
change devices, counts as a step. The Program/
SPL Indicator

2 will flash green twice to con-

firm each button press as you enter commands.

NOTE: While entering commands for Power On of
any device during a macro sequence, press the
Mute button 

(. DO NOT press the Power ON

button

3.

• Remember to press the appropriate Input
Selector button 

4 before functions are

changed to another device. This is also needed for
the AVR Selector button

5 itself, as long as

it’s not lit red and AVR functions shall be
programmed.

3. When all the steps have been entered, press
the Sleep button 

9 to enter the commands.

The red light under the Input Selector

45

will blink and then turn off and the Program/
SPL Indicator

2 will flash green twice to con-

firm the macro to be programmed.

Example: To program the Macro 1

  button

so that it turns on the AVR, TV and a Sat-Receiver,
follow these steps:
• Press the Macro 1 button 

  and Mute (

buttons at the same time and then release them.
• Note that the Program/SPL Indicator will
flash amber.
• Press the AVR Selector

5.

• Press the Mute

( button to store the AVR’s

power on command.
• Press the VID 2 Input Selector button 

4 to

indicate the next command is for “TV”.
• Press the Mute

( button to store the TV

Power On Command.
• Press the VID 3 Input Selector button 

4

to indicate the next command is for “Sat-
Receiver”.
• Press the Mute

( button to store the Sat-

Receiver Power On command.
• Press the Sleep/Channel Up button 

9 to

complete the process and store the macro
sequence.

After following these steps, each time you press
the Macro 1 button 

 , the remote will send

all Power On commands.

Erasing Macro Commands
To remove the commands that have been pro-
grammed into one of the Macro buttons, follow
these steps:

1. Press the Mute button

( and the Macro

button

  that contains the commands you

wish to erase.

2. Note that the Program/SPL Indicator

2

will flash amber, and the red LED under the
Input Selector

45 last used will turn on.

3. Within ten seconds, press the Surround
Mode Selector/Channel Down button

A.

4. The red LED under the Selector will go out,
and the Program/SPL Indicator

2 will turn

green and flash three times before it goes out.

5. When the Program/SPL Indicator

2 goes

out, the Macro has been erased.

Once the AVR’s remote has been programmed for
the codes of other devices, press the appropriate
Input Selector

4 to change the remote from

control over the AVR to the additional product.
When you press any of these buttons, it will briefly
flash in red to indicate that you have changed the
device being controlled.

When operating a device other than the AVR, the
controls may not correspond exactly to the func-
tion printed on the remote or button. Some com-
mands, such as the volume control, are the same
as they are with the AVR. Other buttons will
change their function so that they correspond to a
secondary label on the remote. For example, the
Sleep and Surround mode selector buttons also
function as the Channel Up and Channel Down
buttons when operating most TV sets, VCRs or
Sat-Receivers.

For some products, however, the function of a
particular button does not follow the command
printed on the remote. In order to see which
function a button controls, consult the Function
List tables printed on page 38. To use those
tables, first check the type of device being
controlled (e.g., TV, VCR). Next, look at the

remote control diagram on page 38. Note that
each button has a number on it.
To find out what function a particular button has
for a specific device, find the button number on
the Function List and then look in the column for
the device you are controlling. For example, but-
ton number 44 is the”Direct” button for the AVR,
but it is the “Favorite” button for many cable tel-
evision boxes and satellite receivers. Button num-
ber 30 is the Delay button for the AVR, but the
Open/Close button for CD players.

Note that the numbers used to describe the
button functions above and on page 38 for the
purposes of describing how a button operates are
a different set of numbers than those used in the
rest of this manual to describe the button func-
tions for the AVR.

Notes on Using the AVR 
Remote With Other Devices.
• Manufacturers may use different code sets for
the same product category. For that reason, it is
important that you check to see if the code set
you have entered operates as many controls as
possible. If it appears that only a few functions
operate, check to see if another code set will
work with more buttons.

• Depending on the brand and product type used
the functions listed in the Function List tables
may not correspond with the function the unit
reacts on the command. In these cases it’s a
good idea to edit the reaction of the unit into the
corresponding line of the table or to set up a sep-
arate list.

• When a button is pressed on the AVR remote, the
red light under the Input Selector

45 for

the product being operated should flash briefly. If
the Device Control Selector flashes for some but
not all buttons for a particular product, it does
NOT indicate a problem with the remote, but
rather that no function is programmed for the
button being pushed.

The AVR’s remote may be programmed to operate
the Volume Control

) and the Mute (

from either the TV or the AVR in conjunction with
any of the devices controlled by the remote. For
example, since the AVR will likely be used as the
sound system for TV viewing, you may wish to
have the AVR’s volume activated although the
remote is set to run the TV. Either the AVR or TV
volume control may be associated with any of the
remote´s devices.

To program the remote for Volume Punch-
Through, follow these steps:

1. Press the Input Selector

4 for the unit you

wish to have associated with the volume control
and the Mute button 

( at the same time until

the red light illuminates under the Input Selector
4 and note that the Program/SPL Indicator

2 will flash amber.