Harman Kardon AVR 132 Service Manual ▷ View online
AVR 132/230
SERVICE MANUAL
harman/kardon
®
Power for the Digital Revolution®
TECHNICAL SPECIFICATIONS
35
Technical Specifications
Audio Section
Stereo Mode
Continuous Average Power (FTC)
Continuous Average Power (FTC)
40 Watts per channel, 20Hz–20kHz,
@ < 0.07% THD, both channels driven into 8 ohms
@ < 0.07% THD, both channels driven into 8 ohms
Five-Channel Surround Modes
Power Per Individual Channel
Power Per Individual Channel
Front L&R channels:
30 Watts per channel,
@ < 0.07% THD, 20Hz–20kHz into 8 ohms
30 Watts per channel,
@ < 0.07% THD, 20Hz–20kHz into 8 ohms
Center channel:
30 Watts, @ < 0.07% THD, 20Hz–20kHz into 8 ohms
30 Watts, @ < 0.07% THD, 20Hz–20kHz into 8 ohms
Surround channels:
30 Watts per channel,
@ < 0.07% THD, 20Hz–20kHz into 8 ohms
30 Watts per channel,
@ < 0.07% THD, 20Hz–20kHz into 8 ohms
Input Sensitivity/Impedance
Linear (High Level)
200mV/47kohms
Signal-to-Noise Ratio (IHF-A)
95dB
Surround System Adjacent Channel Separation
Analog Decoding
40dB
(Pro Logic, etc.)
Dolby Digital (AC-3)
Dolby Digital (AC-3)
55dB
DTS
55dB
Frequency Response
@ 1W (+0dB, –3dB)
10Hz–100kHz
High Instantaneous
Current Capability (HCC)
Current Capability (HCC)
±25 Amps
Transient Intermodulation
Distortion (TIM)
Distortion (TIM)
Unmeasurable
Rise Time
16 µsec
Slew Rate
40V/µsec
FM Tuner Section
Frequency Range
87.5–108MHz
Usable Sensitivity
IHF 1.3 µV/13.2dBf
Signal-to-Noise Ratio
Mono/Stereo: 70/65dB (DIN)
Distortion
Mono/Stereo: 0.15/0.3%
Stereo Separation
35dB @ 1kHz
Selectivity
±400kHz: 70dB
Image Rejection
80dB
IF Rejection
90dB
AM Tuner Section
Frequency Range 522–1
620kHz
Signal-to-Noise Ratio
45dB
Usable Sensitivity
Loop: 500µV
Distortion
1kHz, 50% Mod: 0.8%
Selectivity
±10kHz: 30dB
Video Section
Video Format
PAL/NTSC
Input Level/Impedance
1Vp-p/75 ohms
Output Level/Impedance 1Vp-p/75 ohms
Video Frequency
Response
Video Frequency
Response
10Hz–8MHz (–3dB)
General
Power Requirement
AC 220-240V/50Hz
Power Consumption
72W idle, 580W maximum
(2 channels driven)
(2 channels driven)
Dimensions (Max)
Width
440mm
Height
165mm
Depth
382mm
Weight
9.6 kg
Depth measurement includes knobs, buttons and terminal connections.
Height measurement includes feet and chassis.
All features and specifications are subject to change without notice.
Height measurement includes feet and chassis.
All features and specifications are subject to change without notice.
Harman Kardon is a registered trademark.
*Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the Double-D symbol are
trademarks of Dolby Laboratories, Inc.
Confidential Unpublished Works. ©1992–1999 Dolby Laboratories, Inc.
All rights reserved.
“Dolby”, “Pro Logic”, and the Double-D symbol are
trademarks of Dolby Laboratories, Inc.
Confidential Unpublished Works. ©1992–1999 Dolby Laboratories, Inc.
All rights reserved.
†"DTS" and "DTS Neo:6" are registered trademarks of DTS, Inc. "96/24"
is a trademark of DTS, Inc.
is a trademark of DTS, Inc.
Logic 7 is a registered trademark of Lexicon, Inc.
29782_AVR132_ENG_sort 10/08/06 16:45 Side 35
SAFETY PRECAUTIONS
The following check should be performed for the continued
protection of the customer and service technician.
protection of the customer and service technician.
LEAKAGE CURRENT CHECK
Measure leakage current to a known earth ground (water
pipe, conduit, etc.) by connecting a leakage current tester
between the earth ground and all exposed metal parts of the
appliance (input/output terminals, screwheads, metal
overlays, control shaft, etc.). Plug the AC line cord of the
appliance directly into a 120V AC 60Hz outlet and turn the
AC power switch on. Any current measured must not exceed
o.5mA.
pipe, conduit, etc.) by connecting a leakage current tester
between the earth ground and all exposed metal parts of the
appliance (input/output terminals, screwheads, metal
overlays, control shaft, etc.). Plug the AC line cord of the
appliance directly into a 120V AC 60Hz outlet and turn the
AC power switch on. Any current measured must not exceed
o.5mA.
ANY MEASUREMENTS NOT WITHIN THE LIMITS
OUTLINED ABOVE ARE INDICATIVE OF A
POTENTIAL SHOCK HAZARD AND MUST BE
CORRECTED BEFORE RETURNING THE APPLIANCE
TO THE CUSTOMER.
OUTLINED ABOVE ARE INDICATIVE OF A
POTENTIAL SHOCK HAZARD AND MUST BE
CORRECTED BEFORE RETURNING THE APPLIANCE
TO THE CUSTOMER.
Device
under
test
Test all
exposed metal
surfaces
exposed metal
surfaces
Also test with
plug reversed
(Using AC adapter
plug as required)
plug reversed
(Using AC adapter
plug as required)
AC Leakage Test
Leakage
current
tester
current
tester
Reading should
not be above
0.5mA
not be above
0.5mA
Earth
ground
ground
FRONT PANEL CONTROLS
5
Main Power Switch: Press this button to
apply power to the AVR. When the switch is
pressed in, the unit is placed in a Standby
mode, as indicated by the orange LED
apply power to the AVR. When the switch is
pressed in, the unit is placed in a Standby
mode, as indicated by the orange LED
2. This
button MUST be pressed in to operate the unit.
To turn the unit off completely and prevent the
use of the remote control, this switch should be
pressed until it pops out from the front panel
so that the word “OFF” may be read at the top
of the switch.
To turn the unit off completely and prevent the
use of the remote control, this switch should be
pressed until it pops out from the front panel
so that the word “OFF” may be read at the top
of the switch.
NOTE: This switch is normally left in the “ON”
position.
position.
1 System Power Control: When the Main
Power Switch
Power Switch
is “ON,” press this button to
turn on the AVR; press it again to turn the unit
off (to Standby). Note that the Power
Indicator
off (to Standby). Note that the Power
Indicator
2 will turn blue when the unit is on.
2 Power Indicator: This LED will be illumi-
nated in orange when the unit is in the Standby
mode to signal that the unit is ready to be
turned on. When the unit is in operation, the
indicator will turn blue.
nated in orange when the unit is in the Standby
mode to signal that the unit is ready to be
turned on. When the unit is in operation, the
indicator will turn blue.
3 Headphone Jack: This jack may be used to
listen to the AVR’s output through a pair of
headphones. Be certain that the headphones
have a standard 6.3 mm stereo phone plug.
Note that the speakers will automatically be
turned off when the headphones are connected.
listen to the AVR’s output through a pair of
headphones. Be certain that the headphones
have a standard 6.3 mm stereo phone plug.
Note that the speakers will automatically be
turned off when the headphones are connected.
4 Digital Optical 3 Input: Connect the opti-
cal digital audio output of an audio or video prod-
uct to this jack. When the Input is not in use, be
certain to keep the plastic cap installed to avoid
dust contamination that might degrade future
performance.
cal digital audio output of an audio or video prod-
uct to this jack. When the Input is not in use, be
certain to keep the plastic cap installed to avoid
dust contamination that might degrade future
performance.
5 Speaker/Channel Input Indicators: These
indicators are multipurpose, indicating either the
speaker type selected for each channel or the
incoming data-signal configuration. The left, cen-
ter, right, right surround and left surround speaker
indicators are composed of three boxes, while the
subwoofer is a single box. The center box lights
when a “Small” speaker is selected, and the two
outer boxes light when “Large” speakers are
selected. When none of the boxes are lit for the
center, surround or subwoofer channels, no
speaker has been selected for that position. (See
page 16 for more information on configuring
speakers.) The letters inside each of the center
boxes display active input channels. For standard
analog inputs, only the L and R will light, indicat-
ing a stereo input. When a digital source is play-
ing, the indicators will light to display the chan-
nels begin received at the digital input. When the
letters flash, the digital input has been interrupt-
ed. (See page 20 for more information on the
Channel Indicators).
indicators are multipurpose, indicating either the
speaker type selected for each channel or the
incoming data-signal configuration. The left, cen-
ter, right, right surround and left surround speaker
indicators are composed of three boxes, while the
subwoofer is a single box. The center box lights
when a “Small” speaker is selected, and the two
outer boxes light when “Large” speakers are
selected. When none of the boxes are lit for the
center, surround or subwoofer channels, no
speaker has been selected for that position. (See
page 16 for more information on configuring
speakers.) The letters inside each of the center
boxes display active input channels. For standard
analog inputs, only the L and R will light, indicat-
ing a stereo input. When a digital source is play-
ing, the indicators will light to display the chan-
nels begin received at the digital input. When the
letters flash, the digital input has been interrupt-
ed. (See page 20 for more information on the
Channel Indicators).
Front Panel Controls
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
G
H
I
J
Main Power Switch
System Power Control
Power Indicator
Headphone Jack
Digital Optical 3 Input
Speaker/Channel Input Indicator
Surround Mode Group Selector
System Power Control
Power Indicator
Headphone Jack
Digital Optical 3 Input
Speaker/Channel Input Indicator
Surround Mode Group Selector
Tuning
Tuner Band Selector
Preset Stations Selector
Input Source Selector
RDS Select Button
Surround Mode Selector
Surround Mode Indicators
Tuner Band Selector
Preset Stations Selector
Input Source Selector
RDS Select Button
Surround Mode Selector
Surround Mode Indicators
Remote Sensor Window
Main Information Display
Digital Coax 3 Input
Video 3 input jacks
Volume Control
Input Indicators
Main Information Display
Digital Coax 3 Input
Video 3 input jacks
Volume Control
Input Indicators
1
6
7
G
9
D
F
I
J
C
8
B
L
2
4
A
5
E
3
DIGITAL
LOGIC 7
VID 1
DVD
CD
FMAM
TAPE
VID 2
VID 3
PRO LOGIC
3 STEREO
DSP
5 CH. STEREO
SURR. OFF
6 CH
29782_AVR132_ENG_sort 10/08/06 16:45 Side 5
