Harman Kardon ABH-4 (serv.man10) EMC - CB Certificate ▷ View online
page 21 of 42
Report No.SPCLVD31229
TRF No.: I950___D
TRF originator: FIMKO
4
PHYSICAL REQUIREMENTS
Pass
4.1
Stability
Pass
Angle of 10
°
The length and width of the
equipment remarkably
exceed its height.
equipment remarkably
exceed its height.
N/A
Test: force (N) .................................................... : Equipment is not a floor-
standing unit.
N/A
4.2
Mechanical strength
Pass
4.2.1
General
See below.
Pass
4.2.2
Steady force test, 10 N
10N were applied to
components.
components.
No energy or other hazards.
Pass
4.2.3
Steady force test, 30 N
The equipment does not have
any internal enclosures.
any internal enclosures.
N/A
4.2.4
Steady force test, 250 N
250N were applied to other
outer enclosure.
outer enclosure.
No energy or other hazards.
Pass
4.2.5
Impact test
500g steel sphere ball fall,
from 1.3m height onto outer
enclosure.
from 1.3m height onto outer
enclosure.
The test was done with all
enclosure. No safety relevant
damaged.
enclosure. No safety relevant
damaged.
Pass
4.2.6
Drop test
Unit is not hand-held, direct
plug-in, or transportable.
plug-in, or transportable.
N/A
4.2.7
Stress relief
Test is carried out at 84℃, 7
hours. No risk of shrinkage or
distortion on enclosures due
to release of internal stresses.
hours. No risk of shrinkage or
distortion on enclosures due
to release of internal stresses.
Pass
4.2.8
Cathode ray tubes
The equipment does not have
any CRT.
any CRT.
N/A
Picture tube separately certified......................... :
N/A
4.2.9
High pressure lamps
The equipment does not have
any high pressure lamps.
any high pressure lamps.
N/A
4.2.10
Wall or ceiling mounted equipment; force (N) ... : Not wall mounted equipment.
N/A
page 22 of 42
Report No.SPCLVD31229
TRF No.: I950___D
TRF originator: FIMKO
4.3
Design and construction
Pass
4.3.1
Edges and corners
All edges and corners are
judged to be sufficiently well
rounded so as not to
constitute a hazard.
judged to be sufficiently well
rounded so as not to
constitute a hazard.
Pass
4.3.2
Handles and manual controls; force (N).............:
N/A
4.3.3
Adjustable controls
The equipment does not have
a voltage selector.
a voltage selector.
The equipment is auto-
ranging.
ranging.
N/A
4.3.4
Securing of parts
No loosening of parts
impairing creepage distances
or clearances over
supplementary or reinforced
insulation is likely to occur.
impairing creepage distances
or clearances over
supplementary or reinforced
insulation is likely to occur.
Pass
4.3.5
Connection of plugs and sockets
The equipment does not have
any interchangeable
plugs/sockets.
any interchangeable
plugs/sockets.
N/A
4.3.6
Direct plug-in equipment
Not direct plug-in equipment.
N/A
Torque (Nm) .....................................................:
4.3.7
Heating elements in earthed equipment
The equipment does not have
any heating elements.
any heating elements.
N/A
4.3.8
Batteries
No batteries in the equipment.
N/A
4.3.9
Oil and grease
The insulation of the internal
wiring is not exposed to oil,
grease, etc.
wiring is not exposed to oil,
grease, etc.
N/A
4.3.10
Dust, powders, liquids and gases
The equipment does not
produce dust or employ
powders, liquids or gases.
produce dust or employ
powders, liquids or gases.
N/A
4.3.11
Containers for liquids or gases
The equipment does not
contain liquids.
contain liquids.
N/A
4.3.12
Flammable liquids .............................................: The equipment does not use
any flammable liquids.
N/A
Quantity of liquid (l) ...........................................:
N/A
Flash point (
°
C).................................................:
N/A
4.3.13
Radiation; type of radiation ...............................: The equipment does not
generate ionizing radiation or
contain flammable liquids or
gases.
contain flammable liquids or
gases.
N/A
Equipment using lasers
N/A
page 23 of 42
Report No.SPCLVD31229
TRF No.: I950___D
TRF originator: FIMKO
4.4
Protection against hazardous moving parts
N/A
4.4.1
General
Equipment does not have any
hazardous moving parts.
hazardous moving parts.
N/A
4.4.2
Protection in operator access areas
Equipment does not have any
hazardous moving parts.
hazardous moving parts.
N/A
4.4.3
Protection in restricted access locations
Equipment does not have any
hazardous moving parts.
hazardous moving parts.
N/A
4.4.4
Protection in service access areas
Unintentional contact with
hazardous moving parts by
service personnel is unlikely.
hazardous moving parts by
service personnel is unlikely.
N/A
4.5
Thermal requirements
Pass
4.5.1
Temperature rises
See enclosed test record
Pass
Normal load condition per Annex L.................... :
N/A
4.5.2
Resistance to abnormal heat
No parts at hazardous voltage
are directly mounted on
thermoplastic parts.
are directly mounted on
thermoplastic parts.
N/A
4.6
Openings in enclosures
Pass
4.6.1
Top and side openings
No opening on enclosure.
NA
Dimensions (mm) ............................................. :
4.6.2
Bottoms of fire enclosures
No opening on enclosure.
N/A
Construction of the bottom ................................ :
4.6.3
Doors or covers in fire enclosures
The equipment does not have
any doors or covers.
any doors or covers.
N/A
4.6.4
Openings in transportable equipment
No opening on enclosure.
N/A
4.6.5
Adhesives for constructional purposes
Adhesives not used for
securement of internal
barriers or screens.
securement of internal
barriers or screens.
N/A
Conditioning temperature/time........................... :
page 24 of 42
Report No.SPCLVD31229
TRF No.: I950___D
TRF originator: FIMKO
4.7
Resistance to fire
Pass
4.7.1
Reducing the risk of ignition and spread of flame
Method 1: Selection and
application of components
and materials which minimize
the possibility of ignition and
spread of flame.
application of components
and materials which minimize
the possibility of ignition and
spread of flame.
Pass
4.7.2
Conditions for a fire enclosure
With having the following
components:
components:
-
Components with winding
-
Wiring
-
Semiconductor devices,
transistor, diodes,
integrated circuits
transistor, diodes,
integrated circuits
-
Resistors, capacitors,
inductor
inductor
The fire enclosure is required.
Pass
4.7.2.1
Parts requiring a fire enclosure
A fire enclosure covers all
parts.
parts.
Pass
4.7.2.2
Parts not requiring a fire enclosure
Fire enclosure covers all
parts.
parts.
Pass
4.7.3
Materials
Pass
4.7.3.1
General
See below.
Pass
4.7.3.2
Materials for fire enclosures
The fire enclosure is plastic
rated V-0.
rated V-0.
N/A
4.7.3.3
Materials for components and other parts outside
fire enclosures
fire enclosures
Fire enclosure covers all
parts.
parts.
N/A
4.7.3.4
Materials for components and other parts inside
fire enclosures
fire enclosures
All internal materials are rated
V-2 or better or are mounted
on a PWB rated V-1 or better.
V-2 or better or are mounted
on a PWB rated V-1 or better.
Internal wiring is UL
Recognized, marked VW-1 or
FT-1 and strapped by
individual cable ties (where
needed).
Recognized, marked VW-1 or
FT-1 and strapped by
individual cable ties (where
needed).
See Table 1.5 for material
information.
information.
Pass
4.7.3.5
Materials for air filter assemblies
The equipment does not have
any air filters.
any air filters.
N/A
4.7.3.6
Materials used in high-voltage components
No high-voltage components.
N/A
Click on the first or last page to see other ABH-4 (serv.man10) service manuals if exist.