Sony KD-27FS170 Service Manual ▷ View online
KD-27FS170/32FS170/36FS170
KD-27FS170/32FS170/36FS170
30
KD-36FS170
- Fix HV Cable using a purse lock (4-089-469-11) take carbon
paint as reference.
- Fix DGC lead wire to DGC's tie wrap with a 9mm purse lock (3-
703-982-02)
paint as reference.
- Fix DGC lead wire to DGC's tie wrap with a 9mm purse lock (3-
703-982-02)
Dress CRT ground behind DGC & pass
beside VD board as shown in picture.
beside VD board as shown in picture.
Behind DGC
KD-27FS170/32FS170/36FS170
KD-27FS170/32FS170/36FS170
31
The following adjustments should be made when a complete realignment
is required or a new picture tube is installed.
is required or a new picture tube is installed.
These adjustments should be performed with rated power supply voltage
unless otherwise noted.
unless otherwise noted.
Set the controls as follows unless otherwise noted:
VIDEO MODE: Pro
PICTURE CONTROL: Normal
BRIGHTNESS CONTROL: Normal
VIDEO MODE: Pro
PICTURE CONTROL: Normal
BRIGHTNESS CONTROL: Normal
SECTION 2: SET-UP ADJUSTMENTS
Perform the adjustments in order as follows:
1.
1.
Beam
Landing
2.
Convergence
3.
Focus
4.
Screen
(G2)
5.
White
Balance
Note Test Equipment Required:
1.
Color Bar Pattern Generator
2.
Degausser
3.
DC Power Supply
4.
Digital
Multimeter
2-1. BEAM LANDING
Before beginning adjustment procedure:
1. Feed in the white pattern signal.
Adjustment Procedure
1. Input a raster signal with the pattern generator.
2. Loosen the defl ection yoke mounting screw, and set the purity
control to the center as shown below:
Purity Control
3. Turn the raster signal of the pattern generator to green.
4. Move the defl ection yoke backward, and adjust with the purity
control so that green is in the center and red and blue are even on
both sides.
both sides.
Blue Red
Green
5. Move the defl ection yoke forward, and adjust so that the entire
screen becomes green.
6. Switch over the raster signal to red and blue and confi rm the
condition.
7. When the position of the defl ection yoke is determined, tighten it
with the defl ection yoke mounting screw.
8. If landing at the corner is not right, adjust by using the disk
magnets.
a
c
b
d
b
a
c
d
Purity control
corrects this area.
Disk magnets
or rotatable disk
magnets correct
these areas (a-d).
Deflection yoke positioning
corrects these areas.
KD-27FS170/32FS170/36FS170
KD-27FS170/32FS170/36FS170
32
2-2. CONVERGENCE
Before starting convergence adjustments:
1
Perform FOCUS, VLIN and VSIZE adjustments.
2. Set BRIGHTNESS control to minimum.
3. Feed in dot pattern.
Vertical Static Convergence
1. Adjust V. STAT magnet to converge red, green and blue dots in the
center of the screen.
B
G
R
Center dot
V.STAT magnet
RV701
H.STAT
B
G
R
2. Tilt the V. STAT magnet and adjust static convergence to open or
close the V. STAT magnet.
When the V. STAT magnet is moved in the direction of arrow a and
b, red, green, and blue dots move as shown below:
b, red, green, and blue dots move as shown below:
B
R
G
B
R
G
R
G B
B
G R
1
2
b
b
b
b
b
b
b
a
a
b
a
a
a
a
3
R
G
B
B
G
R
Horizontal Static Convergence
If the blue dot does not converge with the red and green dots, perform
the following:
1. Move H STAT VR magnet (a) to correct insuffi cient H.Static
the following:
1. Move H STAT VR magnet (a) to correct insuffi cient H.Static
convergence.
B
MC MA
G
NET
PURITY
V.STAT
KD-27FS170/32FS170/36FS170
KD-27FS170/32FS170/36FS170
33
Dynamic Convergence Adjustment
Before performing this adjustment, perform Horizontal and Vertical Static
Convergence Adjustment.
1. Slightly loosen defl ection yoke screw.
Convergence Adjustment.
1. Slightly loosen defl ection yoke screw.
2. Remove defl ection yoke spacers.
3. Move the defl ection yoke for best convergence as
shown below:
B
G
R
G
B
R
G
B
R
R
R
G
B
G
B
G
B
R
B
G
R
G
B
G
B
R
R
G
B
G
G
B
R B
R
R
4. Tighten the defl ection yoke screw.
5. Install the defl ection yoke spacers.
TLH Plate Adjustment
1. Input
crosshatch
pattern.
2. Adjust PICTURE QUALITY to standard, PICTURE and
BRIGHTNESS to 50%, and OTHER to standard.
3
Adjust the Horizontal Convergence of red and blue dots by tilting
the TLH plate on the defl ection yoke.
the TLH plate on the defl ection yoke.
(TLV)
YCH
XCV
TLV
C
Board
Board
RV701
V.STAT
TLH Plate
B R R B
(R)(B) (B)(R)
(R)(B) (B)(R)
TLH+
TLH-
TLH-
4. Adjust XCV core to balance X axis.
5. Adjust YCH VR to balance Y axis.
6. Adjust vertical red and blue convergence with V.TILT (TLV VR.)
Note: Perform adjustment 3-6 while tracking items 1 and 2.
Screen-Corner Convergence
1. Affi x a permalloy assembly corresponding to the misconverged
areas:
b
a
c
d
a
b
d
a-d: screen-corner
misconvergence
c
2-3. FOCUS
1. Adjust FOCUS control for best pictures.
Focus (FV)
Screen (G2)
Click on the first or last page to see other KD-27FS170 service manuals if exist.