Sony HDR-XR150 / HDR-XR150E / HDR-XR155E (serv.man2) Service Manual ▷ View online
HDR-XR150/XR150E/XR155E_L2
1-1
1. SERVICE NOTE
– ENGLISH –
1-3-3. Self-diagnosis Code Table
Self-diagnosis Code
Symptom/State
Correction
Repaired by:
Block
Function
Detailed
Code
C
0
4
0
0
Non-standard battery is used.
Use the InfoLITHIUM battery.
C
0
6
0
0
The battery pack temperature is high.
Change the battery pack or place it in a cool place.
C
1
3
0
1
Memory card is unformatted.
Memory card is broken.
Memory card is broken.
Format the Memory card.
Insert a new Memory card.
Insert a new Memory card.
C
1
3
0
2
Disc access error
Remove the power source. Reconnect it again and operate
your camcorder again.
your camcorder again.
E
2
0
0
0
Flash memory data are rewritten.
Make flash memory data correct value. (Note)
E
6
1
0
0
Difficult to adjust focus
(Cannot initialize focus)
(Cannot initialize focus)
In case zooming is performed by the touch panel operation,
inspect the focus reset sensor (pin
inspect the focus reset sensor (pin
1 to 4, qk
of CN1003
on the VC-590 board).
In case zooming is not performed, inspect the focus motor
drive circuit (IC5306 on the VC-590 board).
In case zooming is not performed, inspect the focus motor
drive circuit (IC5306 on the VC-590 board).
E
6
1
1
0
Zoom operations fault
(Cannot initialize zoom lens.)
(Cannot initialize zoom lens.)
Inspect the lens block zoom MR sensor (pin
qf, wa to wf
of
CN1003 on the VC-590 board) when zooming is performed
when the zoom lever is operated, or the zoom motor drive
circuit (IC5306 on the VC-590 board) when zooming is not
performed.
when the zoom lever is operated, or the zoom motor drive
circuit (IC5306 on the VC-590 board) when zooming is not
performed.
E
6
1
1
1
The abnormalities in initialization of
the focus lens and the abnormalities
in initialization of the zoom lens oc-
curred simultaneously.
the focus lens and the abnormalities
in initialization of the zoom lens oc-
curred simultaneously.
Check both
E
: 61: 00 and E: 61: 10 of the self-diagnosis
code.
E
6
2
0
0
Handshake correction function does
not work well. (With PITCH angular
velocity sensor output stopped.)
not work well. (With PITCH angular
velocity sensor output stopped.)
Inspect PITCH angular velocity sensors (SE6602 on the MS-
431 board) peripheral circuits.
431 board) peripheral circuits.
E
6
2
0
1
Handshake correction function does
not work well. (With YAW angular
velocity sensor output stopped.)
not work well. (With YAW angular
velocity sensor output stopped.)
Inspect YAW angular velocity sensors (SE6603 on the MS-
431 board) peripheral circuits.
431 board) peripheral circuits.
E
9
2
0
1
Battery current value goes over the
max discharge current
max discharge current
Check the remaining battery power because this symptom
maybe depended on the remaining battery level, and confirm
whether or not the symptom is occurred after replacing the
battery.
If the symptom is still occurred, overhaul inspection is
needed.
Connect MS-431 board to VC-590 board via FP-1185 (VC-
MS) flexible board and connect DC/BATT harness to VC-
590 board (this is the minimum connection to periphery).
in the above state, check each output of DC/DC converter
(IC4701).
maybe depended on the remaining battery level, and confirm
whether or not the symptom is occurred after replacing the
battery.
If the symptom is still occurred, overhaul inspection is
needed.
Connect MS-431 board to VC-590 board via FP-1185 (VC-
MS) flexible board and connect DC/BATT harness to VC-
590 board (this is the minimum connection to periphery).
in the above state, check each output of DC/DC converter
(IC4701).
E
9
4
0
0
Fault of writing or erasing the flash
memory
memory
Inspect the flash memory (
IC8101
on the
VC-590
board).
E
9
4
0
2
BGM data error
Inspect the flash memory (
IC8101
on the
VC-590
board). If
it is OK, check the CPU (IC7501 on the VC-590 board).
Note: Start the Adjust Manual in the Adjust Station and refer to the “Destination data write”.
1-1. POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4 V), the power is shut off
so
so
that the unit cannot operate.
These following method is available to prevent this.
Method:
Use the genuine AC power adaptor
1-2. PRECAUTION ON REPLACING THE VC-590 BOARD
Turn on the set and establish a USB connection , save the USB serial data before replacing the board.
DESTINATION DATA
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Start the Adjust Manual in the Adjust Station and execute the “DESTINATON DATA WRITE”.
Start the Adjust Manual in the Adjust Station and execute the “DESTINATON DATA WRITE”.
After the board replacement, the error of the built-in recording media may be displayed.
in this case, execute the [DESTINATION DATA WRITE] then the error will be cleared.
If it is not cleared with [DESTINATION DATA WRITE], format the built-in recording media.
in this case, execute the [DESTINATION DATA WRITE] then the error will be cleared.
If it is not cleared with [DESTINATION DATA WRITE], format the built-in recording media.
USB SERIAL SAVE
When you replace to the repairing board, get the data from the former one.
Start the Adjust Manual in the Adjust Station and perform “USB SERIAL SAVE” to get the data.
Start the Adjust Manual in the Adjust Station and perform “USB SERIAL SAVE” to get the data.
USB SERIAL No.
The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Start the Adjust Manual in the Adjust Station and execute the “USB SERIAL No. INPUT”.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Start the Adjust Manual in the Adjust Station and execute the “USB SERIAL No. INPUT”.
1-3. SELF-DIAGNOSIS FUNCTION
1-3-1. Self-diagnosis Function
When problems occur while the unit is operating, the self-diagnosis function starts working, and displays on the LCD screen what to do.
Details of the self-diagnosis functions are provided in the Instruction manual.
Details of the self-diagnosis functions are provided in the Instruction manual.
1-3-2. Self-diagnosis Display
When problems occur while the unit is operating, the counter of the LCD screen shows a 4-digit display consisting of an alphabet and
numbers, which blinks at 3.2 Hz. This 5-character display indicates the “repaired by:”, “block” in which the problem occurred, and “detailed
code” of the problem.
numbers, which blinks at 3.2 Hz. This 5-character display indicates the “repaired by:”, “block” in which the problem occurred, and “detailed
code” of the problem.
1 1
3 1
C
Repaired by:
Refer to “1-3-3. Self-diagnosis Code Table” .
Indicates the appropriate
step to be taken.
E.g.
31 ....Reload the tape.
32 ....Turn on power again.
step to be taken.
E.g.
31 ....Reload the tape.
32 ....Turn on power again.
Block
Detailed Code
Blinks at 3.2Hz
C : Corrected by customer
H : Corrected by dealer
E : Corrected by service
H : Corrected by dealer
E : Corrected by service
engineer
LCD screen
C : 3 1 : 1 1
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.0 are shown in blue.
Ver. 1.1 2010.02
HDR-XR150/XR150E/XR155E_L2
1-2E
1-1. 修理時の電源供給について
本機では,安定化電源(8.4Vdc)からバッテリ端子に電源を供給した場合,約10秒後にシャットオフし,動作しなくなります。
これを避けるため,下記の方法を用いてください。
これを避けるため,下記の方法を用いてください。
方法:
ACアダプタを使用する。
1-2. VC-590基板交換時の注意
基板交換時は下記の仕向書き込みとUSB SERIAL SAVEが必要です。
仕向けデータ
補修用基板と交換する時,補修用基板に書かれている仕向けデータは元の設定と違っている場合があります。
Adjust StationからAdjust Manualを起動させて「Destination data write」を実行させてください。
Adjust StationからAdjust Manualを起動させて「Destination data write」を実行させてください。
基板を交換した後,内蔵メモリーのエラーがディスプレイに表示される事があります。
この場合は,[DESTINATION DATA WRITE] を実行することでエラーが解消されます。
エラーが解消されない場合は,[DESTINATION DATA WRITE] と共に内蔵メモリーをフォーマットしてください。
この場合は,[DESTINATION DATA WRITE] を実行することでエラーが解消されます。
エラーが解消されない場合は,[DESTINATION DATA WRITE] と共に内蔵メモリーをフォーマットしてください。
USBシリアルセーブ
補修用基板と交換する時,交換前の基板よりUSBシリアルNo.を取得してください。
データの取得はAdjust StationからAdjust Manualを起動させて「USB SERIAL SAVE」を実行させてください。
データの取得はAdjust StationからAdjust Manualを起動させて「USB SERIAL SAVE」を実行させてください。
USBシリアルNo.
セットは,1台毎に異なる固有のID(USB Serial No.)を書き込んだ後,出荷されています。
新品の補修用基板には,このIDが書き込まれていないので,基板交換後にIDを入力する必要があります。
Adjust StationからAdjust Manualを起動させて「USB serial No. input」を実行させてください。
新品の補修用基板には,このIDが書き込まれていないので,基板交換後にIDを入力する必要があります。
Adjust StationからAdjust Manualを起動させて「USB serial No. input」を実行させてください。
1-3. 自己診断機能
1-3-1. 自己診断機能について
本機の動作に不具合が生じたとき,自己診断機能が働き,LCD画面に,どう処置したらよいか判断できる表示を行います。「自
己診断表示」と「サービスモード表示」の2つの表示があります。自己診断機能については取扱説明書にも掲載されています。
己診断表示」と「サービスモード表示」の2つの表示があります。自己診断機能については取扱説明書にも掲載されています。
1-3-2. 自己診断表示
本機の動作に不具合が生じたとき,LCD画面のカウンタ表示部分がアルファベットと数字の4桁表示になり,3.2Hzで点滅し
ます。この5 文字の表示によって対応者分類および不具合の生じたブロックの分類,不具合の詳細コードを示します。
ます。この5 文字の表示によって対応者分類および不具合の生じたブロックの分類,不具合の詳細コードを示します。
1 1
C
1
3
対応者分類
「1-3-3.自己診断コード表」
を参照
を参照
対応方法の違いにより分類
例 31・・・テープを入れ直す
例 31・・・テープを入れ直す
32・・・電源を入れ直す
ブロック分類
詳細コード
3.2Hz点滅
C:お客さま自身で対応
H:販売店で対応
E:サービスエンジニア
H:販売店で対応
E:サービスエンジニア
で対応
LCD画面
C : 3 1 : 1 1
1 1
C
1
3
対応者分類
「1-3-3.自己診断コード表」
を参照
を参照
対応方法の違いにより分類
例 31・・・テープを入れ直す
例 31・・・テープを入れ直す
32・・・電源を入れ直す
ブロック分類
詳細コード
3.2Hz点滅
C:お客さま自身で対応
H:販売店で対応
E:サービスエンジニア
H:販売店で対応
E:サービスエンジニア
で対応
LCD画面
C : 3 1 : 1 1
– JAPANESE –
1-3-3.
自己診断コード表
自己診断コード
症状/状態
対応/方法
対
応
者
応
者
ブロック
機能
詳細
コード
C
0 4
0 0
標準でないバッテリを使用している
インフォリチウムバッテリを使用する。
C
0 6
0 0
バッテリが高温になっている
バッテリを交換するか、バッテリを涼しいところに置
く。
く。
C
1 3
0 1
フォーマットしていないメモリー
カードを入れた
メモリーカードが壊れている
カードを入れた
メモリーカードが壊れている
メモリーカードをフォーマットする。
新しいメモリーカードに交換する。
新しいメモリーカードに交換する。
C
1 3
0 2
アクセスエラー
電源を外し,再度入れ直してから操作する。
E
2 0
0 0
フラッシュメモリが書き換えられて
いる
いる
フラッシュメモリのデータを元の値に戻す。(注意)
E
6 1
0 0
フォーカスが合いにくい
(フォーカスの初期化ができない)
タッチパネルでフォーカス操作をしたときにフォーカ
ス動作をすれば,レンズブロックのフォーカスリセッ
トセンサ(VC-590基板CN1003
ス動作をすれば,レンズブロックのフォーカスリセッ
トセンサ(VC-590基板CN1003
1 ∼ 4, qk
ピン)を点
検する。フォーカス動作をしなければフォーカスモー
タ駆動回路(VC-590基板IC5306)を点検する。
タ駆動回路(VC-590基板IC5306)を点検する。
E
6 1
1 0
ズーム動作の異常(ズームレンズの
初期化ができない)
初期化ができない)
ズームレバーを操作したときにズーム動作をすれ
ば,レンズブロックのズームMRセンサ(VC-590基板
CN1003
ば,レンズブロックのズームMRセンサ(VC-590基板
CN1003
qf, wa ∼ wf
ピン)を点検する。
ズーム動作をしなければズームモータ駆動回路
(VC-590基板IC5306)を点検する。
E
6 1
1 1
フォーカスレンズ初期化異常,ズー
ムレンズ初期化異常の同時発生
ムレンズ初期化異常の同時発生
自己診断コード
E:61:00
とE:61:10の両方を点検
する。
E
6 2
0 0
手振れ補正が効きにくい
(PITCH角速度センサ出力張り付き)
PITCH角速度センサ(MS-431基板SE6602)周辺回路を
点検。
点検。
E
6 2
0 1
手振れ補正が効きにくい
(YAW角速度センサ出力張り付き)
YAW角速度センサ(MS-431基板SE6603)周辺回路を点
検。
検。
E
9 2
0 1
(バッテリーの)電流値が最大放電電
流を超えた
流を超えた
バッテリ残量に依存する場合があるので,バッテリ残
量を確認する。
次にバッテリを交換して症状が出るか確認する。
バッテリを交換しても症状が出る場合は,エラー発
生後に電源が切れてしまうため,分解して確認する,
VC-590基板にMS-431基板をFP-1185 (VC-MS) フレキ
シブル基板で接続し,DC/バッテリハーネスをVC-590
基板に接続した状態 (最小限の接続) でDC / DCコン
バータ (VC-590基板IC4701) の各チャンネル出力を確
認する。
量を確認する。
次にバッテリを交換して症状が出るか確認する。
バッテリを交換しても症状が出る場合は,エラー発
生後に電源が切れてしまうため,分解して確認する,
VC-590基板にMS-431基板をFP-1185 (VC-MS) フレキ
シブル基板で接続し,DC/バッテリハーネスをVC-590
基板に接続した状態 (最小限の接続) でDC / DCコン
バータ (VC-590基板IC4701) の各チャンネル出力を確
認する。
E
9 4
0 0
フラッシュメモリの書込み/消去動
作不良
作不良
フラッシュメモリ(
VC-590
基板
IC8101
)を点検する。
E
9 4
0 2
BGM データ異常
フラッシュメモリ(
VC-590
基板
IC8101
)を点検する。
異常がない場合は,CPU(VC-590基板 IC7501)を点検
する。
する。
注意: Adjust StationからAdjust Manualを起動させて「DESTINATION DATA WRITE」を参照してください。
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.0 are shown in blue.
Ver. 1.1 2010.02
HDR-XR150/XR150E/XR155E_L2
2-1
2. REPAIR PARTS LIST
Follow the disassembly in the numerical order given.
IDENTIFYING PARTS
AC-
DIS-
Link
ACCESSORIES
ASSEMBLY
VC-590
6
BT Panel Section
[Disassembly]
[Exploded
View]
•
MS-431
Board
• FP-1190 Flexible Board
8
Cabinet (R) Section
[Disassembly]
[Exploded
View]
•
LCD
Section
• PD-404 Board
• Cabinet (R) Section
• JK-395 Board
• FP-1183 Flexible Board
• FP-1191 Flexible Board
q;
Lens Section
•
CM-114
Board
1
Cabinet (G) Assy
2
HDD
7
Cabinet (F) Section
4
Cabinet BM Block
9
VC-590 Board
5
Cabinet T Section
3
Cabinet L
(ENGLISH)
NOTE:
• -XX, -X mean standardized parts, so they may have some
• -XX, -X mean standardized parts, so they may have some
differences from the original one.
• Items marked “*” are not stocked since they are seldom re-
quired for routine service. Some delay should be anticipated
when ordering these items.
when ordering these items.
• The mechanical parts with no reference number in the exploded
views are not supplied.
• Due to standardization, replacements in the parts list may
be different from the parts specified in the diagrams or the
components used on the set.
components used on the set.
(JAPANESE)
【使用上の注意】
• ここに記載されている部品は,補修用部品であるため,回
路図及びセットに付いている部品と異なる場合があります。
• -XX,-Xは標準化部品のため,セットに付いている部品と異
なる場合があります。
• *印の部品は常備在庫しておりません。
• Color Indication of Appearance Parts
Example:
Example:
(SILVER) : Cabinet’s Color
(Silver)
: Parts Color
• 外装部品色表示
例:
(SILVER) :セットの色を表す。
(Silver) :部品の色を表す。
The components identified by mark
or dotted line with mark are critical
for safety.
Replace only with part number specified.
or dotted line with mark are critical
for safety.
Replace only with part number specified.
Les composants identifiés par une
marque sont critiques pour la sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
marque sont critiques pour la sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
印の部品,または印付の点線で囲まれた部品は,
安全性を維持するために,重要な部品です。
従って交換時は,必ず指定の部品を使用してください。
安全性を維持するために,重要な部品です。
従って交換時は,必ず指定の部品を使用してください。
• Abbreviation
AUS :
AUS :
Australian
model
BR
: Brazilian model
CH
: Chinese model
CND : Canadian model
HK
HK
: Hong Kong model
KR
: Korea model
NE
: North European model
JE :
Tourist
Model
J
: Japanese Model
Right View
Left View
Front View
Bottom View
Top View
Back View
View Position
Ver. 1.1 2010.02
HDR-XR150/XR150E/XR155E_L2
2-2
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked
of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, don’t pull at wire of connector. It is
possible that a wire is snapped.
• When installing a connector, don’t press down at wire of con-
nector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
修理時の注意
• フラットケーブルおよびフレキシブル基板の端子面に欠け,
折れ等がないことを確認する。
また,コネクタへの接続は,差し込み不足や斜め差しになら
ないように注意する。
• コネクタを取り外す時に,線材部(極細)を持って引っ張ると
断線する恐れがありますので,絶対に線材部(極細)を持って
引っ張らないでください。
引っ張らないでください。
• 線材部(極細)を押さえながらコネクタを差し込むと,線材部
(極細)が断線する恐れがありますので,絶対に線材部(極細)
には負担をかけないでください。
• 金メッキされているフレキシブル基板には,強い負担をかけ
ないでください。
先端の剥がれたメッキ部はカットして
除去してください。
(メッキ破片がコネクタ内に残っている
場合もあるので注意してください)
除去してください。
(メッキ破片がコネクタ内に残っている
場合もあるので注意してください)
– ENGLISH –
– JAPANESE –
Click on the first or last page to see other HDR-XR150 / HDR-XR150E / HDR-XR155E (serv.man2) service manuals if exist.