Sharp LB-1085 (serv.man3) User Manual / Operation Manual ▷ View online
7
Supplied Accessories
Make sure the following accessories are provided with the product.
Remote control unit (x1)
Page 10
R-6 battery (x2)
Page 10
AC cord clamp (x1)
Page 9
AC cord
Page 9
Operation manual
M16 bolt cap (x2)
Do not use an AC cord other than the one supplied with the monitor.
•
When the eye bolts on the top are removed, close the holes by pressing the M16 bolt caps into the holes. To
•
remove the M16 bolt caps, turn them with a screw driver or coin.
For environmental protection!
For environmental protection!
•
Do not dispose of batteries in household waste. Follow the disposal instructions for your area.
QUICK REFERENCE
Installing the LCD Monitor onto a Stand
CAUTION
When the LCD Monitor is installed onto a stand other than the dedicated stand, the installation may be unstable and
•
may cause serious injury.
Installing the LCD Monitor requires special skills and should only be performed by qualifi ed service personnel.
Installing the LCD Monitor requires special skills and should only be performed by qualifi ed service personnel.
•
Customers should not attempt to install the LCD Monitor by themselves. SHARP shall have no liability for any
accidents or damages caused by improper installation.
Secure the stand with anchor bolts to prevent the LCD Monitor from toppling over.
accidents or damages caused by improper installation.
Secure the stand with anchor bolts to prevent the LCD Monitor from toppling over.
•
8
QUICK REFERENCE
Connecting External Speakers
Speaker Compatibility:
Be sure to use external speakers with an impedance of 4 ohm and a rated
•
input of at least 15W.
Connect the ends of the cables to the SPEAKER terminals as shown
below. Connect the leads to the SPEAKER terminals of the same
polarity.
below. Connect the leads to the SPEAKER terminals of the same
polarity.
R
L
SPEAKER R terminal
To external speaker (right)
To external speaker (right)
SPEAKER L terminal
To external speaker (left)
To external speaker (left)
Make sure to connect the speaker jack and cable polarity (
■
, ) properly.
The speaker terminals have plus and minus polarity.
The cables are also divided into plus and minus.
When connecting the left/right speakers, be sure to connect the plus/minus jacks with the correct cables.
The cables are also divided into plus and minus.
When connecting the left/right speakers, be sure to connect the plus/minus jacks with the correct cables.
CAUTION
Connect the speaker wires to the speakers fi rst, then to the unit.
•
Use speakers with an impedance of 4 ohm as lower impedance speakers can damage the unit.
•
Do not mistake the right and the left channels. The right speaker is the one on the right side when you face
•
the unit.
Do not let the bare speaker wires touch each other.
Do not let the bare speaker wires touch each other.
•
9
QUICK REFERENCE
When transporting the LCD Monitor
Transporting the LCD Monitor requires special skill that should only be performed by qualifi ed service
personnel. Customers should not attempt to do the work themselves.
Transporting the LCD Monitor requires special skill that should only be performed by qualifi ed service
personnel. Customers should not attempt to do the work themselves.
Before turning on the LCD Monitor
1
Connect the AC plug for the LCD Monitor into
the AC outlet.
Be sure to turn OFF the main
•
POWER on the rear
of the LCD Monitor when connecting the cord.
Fix the AC cord as shown below.
Fix the AC cord as shown below.
2
1
3
4
AC outlet
Place the LCD Monitor close to the AC outlet, and
•
keep the power plug within reach.
Do not use an AC cord other than the one supplied
•
with the monitor.
TO PREVENT RISK OF ELECTRIC SHOCK, DO NOT
TO PREVENT RISK OF ELECTRIC SHOCK, DO NOT
•
TOUCH UN-INSULATED PARTS OF ANY CABLES
WITH THE AC CORD CONNECTED.
It is recommended to prepare a dedicated power
WITH THE AC CORD CONNECTED.
It is recommended to prepare a dedicated power
•
line for the LCD Monitor.
2
Push and turn ON the main POWER on the
rear of the LCD Monitor.
Main
POWER
3
Press
POWER on the side of the LCD Monitor.
POWER
The POWER indicator on the front of the LCD
Monitor lights BLUE.
POWER indicator
LCD Monitor angle cannot be adjusted.
•
10
10º
10º
10º
10º
5 m
Remote control sensor
If the remote control fails to operate LCD Monitor functions, replace the batteries in the remote control unit.
1 Open the battery cover.
2 Insert two R-6 batteries
(supplied with the product).
3 Close the battery cover.
CAUTION
Use manganese or alkaline batteries only.
Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.
Do not mix batteries of different types. Different types of batteries have different characteristics.
•
Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause
•
chemical leakage in old batteries.
Remove batteries as soon as they are worn out. Chemicals that leak from batteries that come in contact with skin
•
can cause a rash. If you fi nd any chemical leakage, wipe thoroughly with a cloth.
The batteries supplied with this product may have a shorter life expectancy due to storage conditions.
•
If you will not be using the remote control unit for an extended period of time, remove batteries from it.
•
Never attempt to charge non-rechargeable batteries.
•
Using the Remote Control Unit
Use the remote control unit by pointing it towards the remote control sensor on the LCD Monitor. Objects
between the remote control unit and the remote control sensor may prevent proper operation.
Place the batteries with their terminals corresponding to
•
the (+) and (-) indications in the battery compartment.
QUICK REFERENCE
Cautions regarding the remote control unit
■
Do not expose the remote control unit to shock. In
•
addition, do not expose the remote control unit to
liquids, and do not place in an area with high humidity.
Do not install or place the remote control unit under
liquids, and do not place in an area with high humidity.
Do not install or place the remote control unit under
•
direct sunlight. The heat may cause deformation of the
remote control unit.
The remote control unit may not work properly if the
remote control unit.
The remote control unit may not work properly if the
•
remote control sensor on the LCD Monitor is under
direct sunlight or strong lighting. In such cases, change
the angle of the lighting or the LCD Monitor, or operate
the remote control unit closer to the remote control
sensor.
direct sunlight or strong lighting. In such cases, change
the angle of the lighting or the LCD Monitor, or operate
the remote control unit closer to the remote control
sensor.
The POWER indicator on the LCD Monitor should light BLUE indicating you have
power to the LCD Monitor.
If the POWER indicator on the LCD Monitor still does not light up, press POWER on
If the POWER indicator on the LCD Monitor still does not light up, press POWER on
the remote control to turn the power on.
Click on the first or last page to see other LB-1085 (serv.man3) service manuals if exist.